参数资料
型号: MPC8540VTAQFC
厂商: Freescale Semiconductor
文件页数: 86/104页
文件大小: 0K
描述: MPU POWERQUICC III 783FCPBGA
标准包装: 36
系列: MPC85xx
处理器类型: 32-位 MPC85xx PowerQUICC III
速度: 1.0GHz
电压: 1.3V
安装类型: 表面贴装
封装/外壳: 784-BBGA,FCBGA
供应商设备封装: 783-FCPBGA(29x29)
包装: 托盘
MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1
82
Freescale Semiconductor
Thermal
Figure 47 depicts the primary heat transfer path for a package with an attached heat sink mounted to a
printed-circuit board.
Figure 47. Package with Heat Sink Mounted to a Printed-Circuit Board
The heat sink removes most of the heat from the device. Heat generated on the active side of the chip is
conducted through the silicon and through the lid, then through the heat sink attach material (or thermal
interface material), and finally to the heat sink. The junction-to-case thermal resistance is low enough that
the heat sink attach material and heat sink thermal resistance are the dominant terms.
16.2.3 Thermal Interface Materials
A thermal interface material is required at the package-to-heat sink interface to minimize the thermal
contact resistance. For those applications where the heat sink is attached by spring clip mechanism,
Figure 48 shows the thermal performance of three thin-sheet thermal-interface materials (silicone,
graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure.
As shown, the performance of these thermal interface materials improves with increasing contact pressure.
The use of thermal grease significantly reduces the interface thermal resistance. The bare joint results in a
thermal resistance approximately six times greater than the thermal grease joint.
Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see
Figure 45). Therefore, the synthetic grease offers the best thermal performance, especially at the low
interface pressure.
When removing the heat sink for re-work, it is preferable to slide the heat sink off slowly until the thermal
interface material loses its grip. If the support fixture around the package prevents sliding off the heat sink,
the heat sink should be slowly removed. Heating the heat sink to 40-50C with an air gun can soften the
interface material and make the removal easier. The use of an adhesive for heat sink attach is not
recommended.
External Resistance
Internal Resistance
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
(Note the internal versus external package resistance)
相关PDF资料
PDF描述
MPC8541VTAQF IC MPU POWERQUICC III 783-FCPBGA
MPC8544EAVTARJA IC MPU POWERQUICC III 783-FCBGA
MPC8548ECVTAQGB MPU POWERQUICC III 783-PBGA
MPC8555VTAQF IC MPU POWERQUICC III 783-FCPBGA
MPC855TCVR66D4 IC MPU POWERQUICC 66MHZ 357-PBGA
相关代理商/技术参数
参数描述
MPC8541CPXAJD 功能描述:微处理器 - MPU PQ 37 LITE 8555 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8541CVTAJD 功能描述:微处理器 - MPU PQ 37 LITE 8555 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8541E PXAJD 制造商:FREESCALE-SEMI 功能描述:
MPC8541ECPXAJD 功能描述:微处理器 - MPU PQ 37 LITE 8555E RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8541ECPXALF 功能描述:微处理器 - MPU PQ 37 LITE 8555E RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324