- 您现在的位置：买卖IC网 > PDF目录15054 > NCP5211DR2G (ON Semiconductor)IC REG CTRLR BUCK PWM 14-SOIC PDF资料下载
参数资料
| 型号： | NCP5211DR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 14-SOIC |
| 产品变化通告： | Product Obsolescence 19/Dec/2008 |
| 标准包装： | 2,500 |
| PWM 型： | 电流/电压模式，V²? |
| 输出数： | 1 |
| 频率 - 最大： | 900kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 14 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
NCP5211
q SA is the sink?to?ambient thermal impedance of the
heatsink assuming direct mounting of the MOSFET (no
thermal “pad” is used).
T J is the specified maximum allowed junction
temperature.
T A is the worst case ambient operating temperature.
For TO?220 and TO?263 packages, standard FR?4
copper clad circuit boards will have approximate thermal
resistances ( q SA ) as shown below:
R OSC Selection
The switching frequency is programmed by selecting the
resistor connected between the R OSC pin and SGND (pin 7).
The grounded side of this resistor should be directly
connected to the SGND pin, without any other currents
flowing between the bottom of the resistor and the pin. Also,
avoid running any noisy signals under the resistor, since
injected noise could cause frequency jitter. The graph in
Figure 6 shows the required resistance to program the
frequency. Below 500 kHz, the following formula is
Pad Size
(in 2 /mm 2 )
0.5/323
0.75/484
1.0/645
1.5/968
2.0/1290
2.5/1612
Single?Sided
1 oz. Copper
60?65 ° C/W
55?60 ° C/W
50?55 ° C/W
45?50 ° C/W
38?42 ° C/W
33?37 ° C/W
accurate:
R + 17544 fSW * 4 k W
where f SW is the switching frequency in kHz.
140
120
100
80
As with any power design, proper laboratory testing
should be performed to insure the design will dissipate the
required power under worst case operating conditions.
Variables considered during testing should include
maximum ambient temperature, minimum airflow,
60
40
20
maximum input voltage, maximum loading, and component
variations (i.e. worst case MOSFET R DS(on) ). Also, the
0
0
100
200
300 400 500 600
700
800
inductors and capacitors share the MOSFET’s heatsinks and
will add heat and raise the temperature of the circuit board
and MOSFET. For any new design, its advisable to have as
much heatsink area as possible ? all too often new designs
are found to be too hot and require re?design to add
heatsinking.
Compensation Capacitor Selection
The nominal output current capability of the error amp is
30 m A. This current charging the capacitor on the COMP pin
is used as soft?start for the converter. The COMP pin is going
to ramp up to a voltage level that is within 70 mV of what V FFB
is going to be when in regulation. This is the voltage that will
determine the soft?start. Therefore, the COMP capacitor can
be established by the following relationship:
Frequency (kHz)
Figure 6. Frequency vs. R OSC
Differential Remote Sense Operation
The ability to implement fully differential remote sense is
provided by the NCP5211. The positive remote sense is
implemented by bringing the output remote sense connection
to the positive load connection. A low value resistor is
connected from Vout to the feedback point at the regulator to
provide feedback in the instance when the remote sense point
is not connected.
The negative remote sense connection is provided by
connecting the SGND of the NCP5211 to the negative of the
load return. Again, a low value resistor should be connected
C + 30 m A
soft start
VFFB(REG)
between SGND and LGND at the regulator to provide
feedback in the instance when the remote sense point is not
where:
soft?start = output ramp?up time
V FFB(REG) = V FFB voltage when in regulation
30 m A = COMP output current, typ.
The COMP output current range is given in the data sheet
and will affect the ramp?up time. The value of the capacitor on
the COMP pin will have an effect on the loop response and the
transient response of the converter. Transient response can be
enhanced by the addition of a parallel combination of a resistor
and capacitor between the COMP pin and the comp capacitor.
connected. The maximum voltage differential between the
three grounds for this part is 200 mV.
Feedback Divider Selection
The feedback voltage measured at V FB during normal
regulation will be 1.0 V. This voltage is compared to an internal
1.0 V reference and is used to regulate the output voltage. The
bias current into the error amplifier is 1.0 m A max, so select the
resistor values so that this current does not add an excessive
offset voltage.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| GEM22DTBT-S273 | CONN EDGECARD 44POS R/A .156 SLD |
| GEM22DTAT-S273 | CONN EDGECARD 44POS R/A .156 SLD |
| GBA30DRMZ-S273 | CONN EDGECARD 60POS .125 SQ WW |
| EMM08DRST-S273 | CONN EDGECARD 16POS DIP .156 SLD |
| EBM22DRST-S273 | CONN EDGECARD 44POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5212A | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Single Synchronous Step-Down Controller |
| NCP5212A_09 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Single Synchronous Step-Down Controller |
| NCP5212AGEVB | 功能描述:BOARD EVAL NCP5212A RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| NCP5212AMNTXG | 功能描述:DC/DC 开关控制器 SYNC STEP DOWN CTRL RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5212T | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Single Synchronous Step-Down Controller |
发布紧急采购，3分钟左右您将得到回复。