- 您现在的位置：买卖IC网 > PDF目录224618 > NX25P16-VSI (WINBOND ELECTRONICS CORP) 16M X 1 FLASH 2.7V PROM, PDSO8 PDF资料下载
参数资料
| 型号： | NX25P16-VSI |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 16M X 1 FLASH 2.7V PROM, PDSO8 |
| 封装： | 0.208 INCH, SOIC-8 |
| 文件页数： | 15/43页 |
| 文件大小： | 918K |
| 代理商： | NX25P16-VSI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
W25P80 / W25P16 / W25P32
- 22 -
9.2.10 Chip Erase (C7h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A
Write Enable instruction must be executed before the device will accept the Chip Erase Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and
shifting the instruction code “C7h”. The Chip Erase instruction sequence is shown in figure 12.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip
Erase instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction
will commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in
progress, the Read Status Register instruction may still be accessed to check the status of the BUSY
bit. The BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is
ready to accept other instructions again. After the Chip Erase cycle has finished the Write Enable
Latch (WEL) bit in the Status Register is cleared to 0. The Chip Erase instruction will not be executed
if any page is protected by the Block Protect (BP2, BP1, BP0) bits (see Status Register Memory
Protection table).
Figure 12. Chip Erase Instruction Sequence Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| NX3225SA-100.000M-STD-CSR-3 | QUARTZ CRYSTAL RESONATOR, 100 MHz |
| NX5A0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| NX5B0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| NX5C0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| NX5G0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NX25P20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:1M BIT 2M BIT AND 4M BIT SERIAL FLASH MEMORY WITH 10MHZ SPI |
| NX25P40 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:1M BIT 2M BIT AND 4M BIT SERIAL FLASH MEMORY WITH 10MHZ SPI |
| NX-25TA-CV1 | 制造商:HRS 制造商全称:HRS 功能描述:I/O Card Interface Connectors |
| NX-25TA-CV1(50) | 功能描述:记忆卡连接器 PC CARD FRAME KIT ACCESRY PLUG CVR RoHS:否 制造商:Yamaichi Electronics 产品:Card Connectors 卡类型:microSD 类型: 节距: 方向: 安装风格:SMD/SMT 端接类型: 排数: 触点数量: 电流额定值:0.5 A 电压额定值:50 V |
| NX-25T-BS | 制造商:Hirose 功能描述:234-0074-0-00 EACH |
发布紧急采购，3分钟左右您将得到回复。