- 您现在的位置：买卖IC网 > Datasheet目录347 > P0528 (Terasic Technologies Inc)BOARD DEV DE1 ALTERA Datasheet资料下载
参数资料
| 型号： | P0528 |
| 厂商： | Terasic Technologies Inc |
| 文件页数： | 27/56页 |
| 文件大小： | 0K |
| 描述： | BOARD DEV DE1 ALTERA |
| 标准包装： | 1 |
| 类型： | FPGA |
| 适用于相关产品： | Cyclone II 2C20 |
| 所含物品： | DE1 板，电源，USB 线缆，塑料盖和软件 |
| 配用： | P0033-ND - BOARD ADAPTER HSMC TO GPIO P0006-ND - BOARD ADAPTER THDB-SUM P0001-ND - MODULE DIGITAL CAMERA 5MP (D5M) P0307-ND - KIT DEV 4.3" LCD TOUCH PANEL |
| 相关产品： | 544-2107-ND - IC CYCLONE II FPGA 20K 240-PQFP 544-2106-ND - IC CYCLONE II FPGA 20K 240-PQFP 544-2105-ND - IC CYCLONE II FPGA 20K 484-FBGA 544-2104-ND - IC CYCLONE II FPGA 20K 484-FBGA 544-2103-ND - IC CYCLONE II FPGA 20K 256-FBGA 544-2102-ND - IC CYCLONE II FPGA 20K 256-FBGA 544-2101-ND - IC CYCLONE II FPGA 20K 484-FBGA 544-1781-ND - IC CYCLONE II FPGA 20K 256-FBGA 544-1670-ND - IC CYCLONE II FPGA 20K 484-FBGA 544-1669-ND - IC CYCLONE II FPGA 20K 484-FBGA 更多... |
| 其它名称： | DE1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
DE1 User Manual
Figure 4.1 illustrates the JTAG configuration setup. To download a configuration bit stream into the
Cyclone II FPGA, perform the following steps:
?
?
?
?
Ensure that power is applied to the DE1 board
Connect the supplied USB cable to the USB Blaster port on the DE1 board (see Figure 2.1)
Configure the JTAG programming circuit by setting the RUN/PROG switch (on the left side
of the board) to the RUN position.
The FPGA can now be programmed by using the Quartus II Programmer module to select a
configuration bit stream file with the . sof filename extension
USB Blaster Circuit
Quartus II
Programmer
USB
MAX
3128
PROG/RUN
"RUN"
JTAG Config Signals
JTAG UART
Auto
Power-on Config
JTAG Config Port
EPCS4
Serial
FPGA
Configuration
Device
Figure 4.1. The JTAG configuration scheme.
Configuring the EPCS4 in AS Mode
Figure 4.2 illustrates the AS configuration set up. To download a configuration bit stream into the
EPCS4 serial EEPROM device, perform the following steps:
?
?
?
?
?
Ensure that power is applied to the DE1 board
Connect the supplied USB cable to the USB Blaster port on the DE1 board (see Figure 2.1)
Configure the JTAG programming circuit by setting the RUN/PROG switch (on the left side
of the board) to the PROG position.
The EPCS4 chip can now be programmed by using the Quartus II Programmer module to
select a configuration bit stream file with the . pof filename extension
Once the programming operation is finished, set the RUN/PROG switch back to the RUN
position and then reset the board by turning the power switch off and back on; this action
causes the new configuration data in the EPCS4 device to be loaded into the FPGA chip.
25
相关PDF资料 |
PDF描述 |
|---|---|
| P100-001 | ADAPTER DB9F TO DB25M 1' |
| P2041RDB-PA | BOARD REFERENCE DESIGN P2041 |
| P25E-060S-EA | CONN SOCKET 60POS .050" GOLD |
| P25E-100S-EA | CONN SOCKET 100POS .050" GOLD |
| P25LE-068S-DA | CONN SOCKET 68POS .050" GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P0531961H | 制造商:EUDYNA 制造商全称:Eudyna Devices Inc 功能描述:1.9 GHz band Power Amplifier Module |
| P0531981H | 制造商:EUDYNA 制造商全称:Eudyna Devices Inc 功能描述:1.9 GHz band Power Amplifier Module |
| P0537242 | 制造商:FCI 功能描述:.112 X 3/4 SCREW |
| P054-006 | 功能描述:交流电源线 AC POWER CORD SCHUKO CEE RoHS:否 制造商:Schaffner 地区:North American 插头:NEMA 5-15P 插座:C13 Locking 功率额定值:2500 W 电流额定值:10 A 线规 - 美国线规（AWG）:18 电压额定值:250 V 长度:6 ft 屏蔽: 外壳颜色:Black |
| P054-008 | 制造商:Tripp Lite 功能描述:8 FT. POWER CORD (IEC-320-C13 TO SCHUKO CEE 7/7) - Bulk |
发布紧急采购，3分钟左右您将得到回复。