- 您现在的位置：买卖IC网 > PDF目录296761 > P89LPC925FDH (NXP Semiconductors N.V.) 8-bit microcontrollers with accelerated two-clock 80C51 core 4 kB-8 kB 3 V low-power Flash with 8-bit A-D converter PDF资料下载
参数资料
| 型号： | P89LPC925FDH |
| 厂商： | NXP Semiconductors N.V. |
| 元件分类： | 8位微控制器 |
| 英文描述： | 8-bit microcontrollers with accelerated two-clock 80C51 core 4 kB-8 kB 3 V low-power Flash with 8-bit A-D converter |
| 封装： | P89LPC924FDH<SOT360-1 (TSSOP20)|<<http://www.nxp.com/packages/SOT360-1.html<1<Always Pb-free,;P89LPC925FDH<SOT360-1 (TSSOP20)|<<http://www.nxp.com/packages/SOT360-1.html& |
| 文件页数： | 15/49页 |
| 文件大小： | 233K |
| 代理商： | P89LPC925FDH |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Philips Semiconductors
P89LPC924/925
8-bit microcontrollers with accelerated two-clock 80C51 core
Product data
Rev. 03 — 15 December 2004
22 of 49
9397 750 14471
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
8.11 Data RAM arrangement
The 256 bytes of on-chip RAM are organized as shown in Table 5.
8.12 Interrupts
The P89LPC924/925 uses a four priority level interrupt structure. This allows great
exibility in controlling the handling of the many interrupt sources. The
P89LPC924/925 supports 13 interrupt sources: A/D converter, external interrupts 0
and 1, timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx/Tx,
brownout detect, watchdog/real-time clock, I2C, keyboard, and comparators 1 and 2.
Each interrupt source can be individually enabled or disabled by setting or clearing a
bit in the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a
global disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt,
but not by another interrupt of the same or lower priority. The highest priority interrupt
service cannot be interrupted by any other interrupt source. If two requests of
different priority levels are pending at the start of an instruction, the request of higher
priority level is serviced.
If requests of the same priority level are pending at the start of an instruction, an
internal polling sequence determines which request is serviced. This is called the
arbitration ranking. Note that the arbitration ranking is only used to resolve pending
requests of the same priority level.
8.12.1
External interrupt inputs
The P89LPC924/925 has two external interrupt inputs as well as the Keypad Interrupt
function. The two interrupt inputs are identical to those present on the standard
80C51 microcontrollers.
These external interrupts can be programmed to be level-triggered or edge-triggered
by setting or clearing bit IT1 or IT0 in Register TCON.
In edge-triggered mode if successive samples of the INTn pin show a HIGH in one
cycle and a LOW in the next cycle, the interrupt request ag IEn in TCON is set,
causing an interrupt request.
If an external interrupt is enabled when the P89LPC924/925 is put into Power-down
or Idle mode, the interrupt will cause the processor to wake-up and resume operation.
Refer to Section 8.15 “Power reduction modes” for details.
Table 5:
On-chip data memory usages
Type
Data RAM
Size (bytes)
DATA
Memory that can be addressed directly and indirectly
128
IDATA
Memory that can be addressed indirectly
256
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC9301FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash |
| P89LPC931A1FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash |
| P89LPC930FDH | 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM |
| P89LPC931FDH | 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM |
| P89LPC9321FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC925FDH,529 | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC925FDH-S | 制造商:NXP Semiconductors 功能描述:MCU 8-bit P89 80C51 CISC 8KB Flash 2.5V/3.3V 20-Pin TSSOP |
| P89LPC925FN,129 | 功能描述:8位微控制器 -MCU 8K FL/256B RAM/I2C/UART/ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC925FN-S | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC92X1 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB 3 V byte-erasable flash with 8-bit ADC |
发布紧急采购，3分钟左右您将得到回复。