- 您现在的位置：买卖IC网 > PDF目录296761 > P89LPC925FDH (NXP Semiconductors N.V.) 8-bit microcontrollers with accelerated two-clock 80C51 core 4 kB-8 kB 3 V low-power Flash with 8-bit A-D converter PDF资料下载
参数资料
| 型号： | P89LPC925FDH |
| 厂商： | NXP Semiconductors N.V. |
| 元件分类： | 8位微控制器 |
| 英文描述： | 8-bit microcontrollers with accelerated two-clock 80C51 core 4 kB-8 kB 3 V low-power Flash with 8-bit A-D converter |
| 封装： | P89LPC924FDH<SOT360-1 (TSSOP20)|<<http://www.nxp.com/packages/SOT360-1.html<1<Always Pb-free,;P89LPC925FDH<SOT360-1 (TSSOP20)|<<http://www.nxp.com/packages/SOT360-1.html& |
| 文件页数： | 28/49页 |
| 文件大小： | 233K |
| 代理商： | P89LPC925FDH |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Philips Semiconductors
P89LPC924/925
8-bit microcontrollers with accelerated two-clock 80C51 core
Product data
Rev. 03 — 15 December 2004
34 of 49
9397 750 14471
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
8.21.2
Comparator interrupt
Each comparator has an interrupt ag contained in its conguration register. This ag
is set whenever the comparator output changes state. The ag may be polled by
software or may be used to generate an interrupt. The two comparators use one
common interrupt vector. If both comparators enable interrupts, after entering the
interrupt service routine, the user needs to read the ags to determine which
comparator caused the interrupt.
8.21.3
Comparators and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is
activated, but both comparators are disabled automatically in Total Power-down
mode. If a comparator interrupt is enabled (except in Total Power-down mode), a
change of the comparator output state will generate an interrupt and wake up the
processor. If the comparator output to a pin is enabled, the pin should be congured
in the push-pull mode in order to obtain fast switching times while in Power-down
mode. The reason is that with the oscillator stopped, the temporary strong pull-up that
normally occurs during switching on a quasi-bidirectional port pin does not take
place.
Comparators consume power in Power-down and Idle modes, as well as in the
normal operating mode. This fact should be taken into account when system power
consumption is an issue. To minimize power consumption, the user can disable the
comparators via PCONA.5, or put the device in Total Power-down mode.
8.22 Keypad interrupt (KBI)
The Keypad Interrupt function is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can
be used for bus address recognition or keypad recognition. The user can congure
the port via SFRs for different tasks.
The Keypad Interrupt Mask Register (KBMASK) is used to dene which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN)
is used to dene a pattern that is compared to the value of Port 0. The Keypad
Interrupt Flag (KBIF) in the Keypad Interrupt Control Register (KBCON) is set when
the condition is matched while the Keypad Interrupt function is active. An interrupt will
be generated if enabled. The PATN_SEL bit in the Keypad Interrupt Control Register
(KBCON) is used to dene equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x
series, the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then
any key connected to Port 0 which is enabled by the KBMASK register will cause the
hardware to set KBIF and generate an interrupt if it has been enabled. The interrupt
may be used to wake up the CPU from Idle or Power-down modes. This feature is
particularly useful in handheld, battery-powered systems that need to carefully
manage power consumption yet also need to be convenient to use.
In order to set the ag and cause an interrupt, the pattern on Port 0 must be held
longer than 6 CCLKs.
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC9301FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash |
| P89LPC931A1FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash |
| P89LPC930FDH | 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM |
| P89LPC931FDH | 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM |
| P89LPC9321FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC925FDH,529 | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC925FDH-S | 制造商:NXP Semiconductors 功能描述:MCU 8-bit P89 80C51 CISC 8KB Flash 2.5V/3.3V 20-Pin TSSOP |
| P89LPC925FN,129 | 功能描述:8位微控制器 -MCU 8K FL/256B RAM/I2C/UART/ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC925FN-S | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC92X1 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB 3 V byte-erasable flash with 8-bit ADC |
发布紧急采购，3分钟左右您将得到回复。