参数资料
型号: PCA9685PW/Q900,118
厂商: NXP Semiconductors
文件页数: 28/51页
文件大小: 0K
描述: IC PWM CTLR LED DVR 28TSSOP
产品培训模块: I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 16
内部驱动器:
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz,50MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 28-TSSOP
包装: 标准包装
工作温度: -40°C ~ 85°C
其它名称: 568-5931-6
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I 2 C-bus LED controller
7.7 Using the PCA9685 with and without external drivers
The PCA9685 LED output drivers are 5.5 V only tolerant and can sink up to 25 mA at 5 V.
If the device needs to drive LEDs to a higher voltage and/or higher current, use of an
external driver is required.
? INVRT bit (MODE2 register) can be used to keep the LED PWM control firmware the
same independently of the type of external driver. This bit allows LED output polarity
inversion/non-inversion only when OE = 0.
? OUTDRV bit (MODE2 register) allows minimizing the amount of external components
required to control the external driver (N-type or P-type device).
Table 11.
Use of INVRT and OUTDRV based on connection to the LEDn outputs when OE = 0 [1]
INVRT OUTDRV Direct connection to LEDn
External N-type driver
External P-type driver
Firmware
External
Firmware
External
Firmware
External
pull-up
resistor
pull-up
resistor
pull-up
resistor
0
0
formulas and LED
output state values
LED current formulas and LED required
limiting R [2]
output state
formulas and LED
output state values
required
inverted
values inverted
apply
0
1
formulas and LED
output state values
LED current formulas and LED not
limiting R [2]
required [3]
output state
formulas and LED
output state values
not required
values apply
inverted
[3]
inverted
1
0
formulas and LED
output state values
LED current formulas and LED required
limiting R
output state
formulas and LED
output state values
required
apply [2]
values apply
inverted
1
1
formulas and LED
LED current formulas and LED not required formulas and LED
not
output state values
apply [2]
limiting R
output state
values inverted
output state values required [4]
apply [4]
[1]
[2]
[3]
[4]
When OE = 1, LED output state is controlled only by OUTNE[1:0] bits (MODE2 register).
Correct configuration when LEDs directly connected to the LEDn outputs (connection to V DD through current limiting resistor).
Optimum configuration when external N-type (NPN, NMOS) driver used.
Optimum configuration when external P-type (PNP, PMOS) driver used.
LED0
+5 V
LED0
+5 V
LED0
+V DD
002aad169
INVRT = 0
OUTDRV = 1
Fig 13. External N-type driver
PCA9685
Product data sheet
002aad170
INVRT = 1
OUTDRV = 1
Fig 14. External P-type driver
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 2 September 2010
002aad171
INVRT = 1
OUTDRV = 0
Fig 15. Direct LED connection
? NXP B.V. 2010. All rights reserved.
28 of 51
相关PDF资料
PDF描述
1-747948-5 CONN D-SUB PLUG 25P 26-30AWG AU
ADT6502SRJZP085RL7 IC TEMP SENSOR MICROPWR SOT23-5
MINT1400A4810L01 MEDICAL INTERNAL PS 400W 48V
R05P212S/X2/P/R8 CONV DC/DC 2W 05VIN 12VOUT
787169-9 CONN 100POS .05 AMPLMT RECP RTAG
相关代理商/技术参数
参数描述
PCA9691BS/1 制造商:NXP Semiconductors 功能描述:IC ADC/DAC 8-BIT I2C 16-HVQFN 制造商:NXP Semiconductors 功能描述:IC, ADC/DAC, 8-BIT, I2C, 16-HVQFN
PCA9691BS/1,118 功能描述:I2C 接口集成电路 ADC/DAC 16-Pin HVQFN EP RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9691BS/1118 制造商:NXP Semiconductors 功能描述:PCA9691BS/HVQFN16/REEL13//1
PCA9691T/1,112 制造商:NXP Semiconductors 功能描述:
PCA9691T/1,118 制造商:NXP Semiconductors 功能描述: