参数资料
型号: PCA9685PW/Q900,118
厂商: NXP Semiconductors
文件页数: 35/51页
文件大小: 0K
描述: IC PWM CTLR LED DVR 28TSSOP
产品培训模块: I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 16
内部驱动器:
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz,50MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 28-TSSOP
包装: 标准包装
工作温度: -40°C ~ 85°C
其它名称: 568-5931-6
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I 2 C-bus LED controller
Question 1: What kind of edge rate control is there on the outputs?
? The typical edge rates depend on the output configuration, supply voltage, and the
applied load. The outputs can be configured as either open-drain NMOS or totem pole
outputs. If the customer is using the part to directly drive LEDs, they should be using it
in an open-drain NMOS, if they are concerned about the maximum I SS and ground
bounce. The edge rate control was designed primarily to slow down the turn-on of the
output device; it turns off rather quickly (~1.5 ns). In simulation, the typical turn-on
time for the open-drain NMOS was ~14 ns (V DD = 3.6 V; C L = 50 pF; R PU = 500 Ω ).
Question 2: Is ground bounce possible?
? Ground bounce is a possibility, especially if all 16 outputs are changed at full current
(25 mA each). There is a fair amount of decoupling capacitance on chip (~50 pF),
which is intended to suppress some of the ground bounce. The customer will need to
determine if additional decoupling capacitance externally placed as close as
physically possible to the device is required.
Question 3: Can I really sink 400 mA through the single ground pin on the package and
will this cause any ground bounce problem due to the PWM of the LEDs?
? Yes, you can sink 400 mA through a single ground pin on the package . Although the
package only has one ground pin, there are two ground pads on the die itself
connected to this one pin. Although some ground bounce is likely, it will not disrupt the
operation of the part and would be reduced by the external decoupling capacitance.
Question 4: I can’t turn the LEDs on or off, but their registers are set properly. Why?
? Check the MODE1 register SLEEP (bit 4) setting. The bit needs to be 0 in order to
enable the clocking. If both clock sources (internal osc and EXTCLK) are turned OFF
(bit 4 = 1), the LEDs cannot be dimmed or blinked.
Question 5: I’m using LEDs with integrated Zener diodes and the IC is getting very hot.
Why?
? The IC outputs can be set to either open-drain or push-pull and default to push-pull
outputs. In this application with the Zener diodes, they need to be set to open-drain
since in the push-pull architecture there is a low resistance path to GND through the
Zener and this is causing the IC to overheat.
PCA9685
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 2 September 2010
? NXP B.V. 2010. All rights reserved.
35 of 51
相关PDF资料
PDF描述
1-747948-5 CONN D-SUB PLUG 25P 26-30AWG AU
ADT6502SRJZP085RL7 IC TEMP SENSOR MICROPWR SOT23-5
MINT1400A4810L01 MEDICAL INTERNAL PS 400W 48V
R05P212S/X2/P/R8 CONV DC/DC 2W 05VIN 12VOUT
787169-9 CONN 100POS .05 AMPLMT RECP RTAG
相关代理商/技术参数
参数描述
PCA9691BS/1 制造商:NXP Semiconductors 功能描述:IC ADC/DAC 8-BIT I2C 16-HVQFN 制造商:NXP Semiconductors 功能描述:IC, ADC/DAC, 8-BIT, I2C, 16-HVQFN
PCA9691BS/1,118 功能描述:I2C 接口集成电路 ADC/DAC 16-Pin HVQFN EP RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9691BS/1118 制造商:NXP Semiconductors 功能描述:PCA9691BS/HVQFN16/REEL13//1
PCA9691T/1,112 制造商:NXP Semiconductors 功能描述:
PCA9691T/1,118 制造商:NXP Semiconductors 功能描述: