参数资料
型号: PCA9685PW/Q900,118
厂商: NXP Semiconductors
文件页数: 6/51页
文件大小: 0K
描述: IC PWM CTLR LED DVR 28TSSOP
产品培训模块: I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 16
内部驱动器:
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz,50MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 28-TSSOP
包装: 标准包装
工作温度: -40°C ~ 85°C
其它名称: 568-5931-6
NXP Semiconductors
Table 2.
PCA9685
16-channel, 12-bit PWM Fm+ I 2 C-bus LED controller
Pin description …continued
Symbol
Pin
TSSOP28
HVQFN28
Type
Description
LED12
LED13
LED14
LED15
OE
A5
EXTCLK
SCL
SDA
V DD
19
20
21
22
23
24
25
26
27
28
16
17
18
19
20
21
22
23
24
25
O
O
O
O
I
I
I
I
I/O
power supply
LED driver 12
LED driver 13
LED driver 14
LED driver 15
active LOW output enable
address input 5
external clock input [2]
serial clock line
serial data line
supply voltage
[1]
[2]
HVQFN28 package die supply ground is connected to both V SS pin and exposed center pad. V SS pin must
be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board
level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad
on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the
PCB in the thermal pad region.
This pin must be grounded when this feature is not used.
7. Functional description
Refer to Figure 1 “ Block    diagram of PCA9685 ” .
7.1 Device addresses
Following a START condition, the bus master must output the address of the slave it is
accessing.
There are a maximum of 64 possible programmable addresses using the 6 hardware
address pins. Two of these addresses, Software Reset and LED All Call, cannot be used
because their default power-up state is ON, leaving a maximum of 62 addresses. Using
other reserved addresses, as well as any other subcall address, will reduce the total
number of possible addresses even further.
7.1.1 Regular I 2 C-bus slave address
The I 2 C-bus slave address of the PCA9685 is shown in Figure 4 . To conserve power, no
internal pull-up resistors are incorporated on the hardware selectable address pins and
they must be pulled HIGH or LOW.
Remark: Using reserved I 2 C-bus addresses will interfere with other devices, but only if
the devices are on the bus and/or the bus will be open to other I 2 C-bus systems at some
later date. In a closed system where the designer controls the address assignment these
addresses can be used since the PCA9685 treats them like any other address. The
LED All Call, Software Reset and PCA9564 or PCA9665 slave address (if on the bus) can
never be used for individual device addresses.
? PCA9685 LED All Call address (1110 000) and Software Reset (0000 0110) which are
active on start-up
PCA9685
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 2 September 2010
? NXP B.V. 2010. All rights reserved.
6 of 51
相关PDF资料
PDF描述
1-747948-5 CONN D-SUB PLUG 25P 26-30AWG AU
ADT6502SRJZP085RL7 IC TEMP SENSOR MICROPWR SOT23-5
MINT1400A4810L01 MEDICAL INTERNAL PS 400W 48V
R05P212S/X2/P/R8 CONV DC/DC 2W 05VIN 12VOUT
787169-9 CONN 100POS .05 AMPLMT RECP RTAG
相关代理商/技术参数
参数描述
PCA9691BS/1 制造商:NXP Semiconductors 功能描述:IC ADC/DAC 8-BIT I2C 16-HVQFN 制造商:NXP Semiconductors 功能描述:IC, ADC/DAC, 8-BIT, I2C, 16-HVQFN
PCA9691BS/1,118 功能描述:I2C 接口集成电路 ADC/DAC 16-Pin HVQFN EP RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9691BS/1118 制造商:NXP Semiconductors 功能描述:PCA9691BS/HVQFN16/REEL13//1
PCA9691T/1,112 制造商:NXP Semiconductors 功能描述:
PCA9691T/1,118 制造商:NXP Semiconductors 功能描述: