- 您现在的位置：买卖IC网 > PDF目录296796 > PCM9211PTR (TEXAS INSTRUMENTS INC) DATACOM, TOKEN RING TRANSCEIVER, PQFP48 PDF资料下载
参数资料
| 型号： | PCM9211PTR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 网络接口 |
| 英文描述： | DATACOM, TOKEN RING TRANSCEIVER, PQFP48 |
| 封装： | GREEN, PLASTIC, LQFP-48 |
| 文件页数： | 41/121页 |
| 文件大小： | 1219K |
| 代理商： | PCM9211PTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页
SBAS495 – JUNE 2010
www.ti.com
The trigger threshold for the ADC can be configured at four different levels below full scale using the
ADLVLTH[1:0] bits in Register 2Eh. The output is post-ADC volume control, allowing finer gain steps to be
configured by changing the ADC volume control.
In a typical application, this level change is done as the system moves into standby, and reset back to 0dB
attenuation when the system wakes up.
The output of this comparator circuit can be ORed along with the INT1 interrupt that is sourced. When the INT1
interrupt is flagged, then the INT1 output register can be read by the host controller.
Real World Application
By using both the S/PDIF lock status on INT0 and the analog level detect output on INT1, a system controller
can place the rest of the system to sleep (such as the Class D amplifier stage, etc). Upon S/PDIF lock, or an
ADC input that is above the preset threshold, the controller can wake up and wake up the rest of the system.
In most implementations, it is suggested that as the system goes into standby, only INT1 be used for the ADC
level detect function. (that is, mask all other INT1 sources). In addition, it is recommended that this function be
implemented one second after startup, in order to allow the internal high-pass filter to settle.
Using such a system allows auto-shutdown, provided that the source moves into its own standby mode (for
example, a TV or a set-top box).
Digital Audio Interface Receiver (RXIN0 to RXIN11)
Input Details for Pins RXIN0 Through RXIN11
Up to 12 single-ended S/PDIF input pins are available. Two of the S/PDIF input pins integrate coaxial amplifiers.
The other 10 pins are designed to be directly connected to CMOS sources or standard S/PDIF optical modules.
Each of the inputs can tolerate 5-V inputs.
The DIR module in the PCM9211 complies with these Digital Audio I/F standards:
S/PDIF
IEC60958 (formerly IEC958)
JEITA CPR-1205 (formerly EIAJ CP-1201/340)
AES3
EBU Tech 3250 (also known as AES/EBU)
In addition, the DIR module within the PCM9211 also meets and exceeds jitter tolerance limits as specified by
IEC60958-3 for sampling frequencies between 28 kHz and 216 kHz.
Each of the physical connections used for these standards (optical, differential, and single-ended) have different
signal levels. Care should be taken to ensure that each of the RXIN pins is not overdriven or underdriven, such
as driving a coaxial 0.2-VPP signal into a CMOS 3.3-V input.
RXIN0 and RXIN1 integrate coaxial input amplifiers. This architecture means that they can be directly connected
to either coaxial input (or RCA/Phono) S/PDIF sources. They can accept a minimum of 0.2VPP. They can also be
connected to maximum 5-V TTL sources, such as optical receivers. (NOTE: Consideration should be made for
electrostatic discharge, or ESD, on the input connectors.)
RXIN2 to RXIN11 are 5-V tolerant TTL level inputs. These inputs are typically used as connections to optical
receiver modules (known as TOSLINK connectors).
RXIN8 through RXIN11 are also part of the MPIO_A (Multipurpose Input/Output A) group. These I/O pins can
either be set as S/PDIF inputs, or reassigned to other functions (see the MPIO section). To configure MPIO_A as
S/PDIF inputs, set Register MPASEL[1:0] to '00'.
Typically, no additional components are required to connect an optical receiver to any RXIN pin. However,
consideration should be given to the output characteristics of the specific receiver modules used, especially if
there is a long printed circuit board (PCB) trace between the receiver and the PCM9211 itself.
For differential inputs (such as the AES/EBU standard), differential to single-ended circuitry is required.
26
Copyright 2010, Texas Instruments Incorporated
Product Folder Link(s): PCM9211
相关PDF资料 |
PDF描述 |
|---|---|
| PCM9211PT | DATACOM, TOKEN RING TRANSCEIVER, PQFP48 |
| PCN11MF | STRIP TERMINAL BLOCK, 1 DECK |
| PCN12E-32S-2.54DSA | 32 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, SOLDER, SOCKET |
| PCN12E-44S-2.54DSA | 44 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, SOLDER, SOCKET |
| PCN12E-50S-2.54DSA | 50 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, SOLDER, SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCM-93 | 功能描述:电线鉴定 Pre-Printed WM Card, Vinyl Cloth, .22" W RoHS:否 制造商:TE Connectivity / Q-Cees 产品:Labels and Signs 类型: 材料:Vinyl 颜色:Blue 宽度:0.625 in 长度:1 in |
| PCM-9342 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
| PCM-9342F-64A1E | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
| PCM-9342FZ2-64A1E | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
| PCM-9342L-64A1E | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
发布紧急采购，3分钟左右您将得到回复。