- 您现在的位置：买卖IC网 > PDF目录11744 > PI7C8150BNDE (Pericom)IC PCI-PCI BRIDGE ASYNC 256-PBGA PDF资料下载
参数资料
| 型号： | PI7C8150BNDE |
| 厂商： | Pericom |
| 文件页数： | 18/109页 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 256-PBGA |
| 标准包装： | 90 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 256-BGA |
| 供应商设备封装： | 256-PBGA（17x17） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 16 of 109
April 2009 – Revision 1.08
Name
Pin #
Type
Description
S_CLKIN
21
H3
I
Secondary Clock Input: Provides timing for all
transactions on the secondary interface.
S_CLKOUT[9:0]
42, 41, 39, 38, 36,
35, 33, 32, 30, 29
M3, M2, N1,
L4, L3, M1, L2,
L1, K3, K2
O
Secondary Clock Output: Provides secondary clocks
phase synchronous with the P_CLK in synchronous
mode.
When these clocks are used, one of the clock outputs
must be fed back to S_CLKIN. Unused outputs may be
disabled by:
1. Writing the secondary clock disable bits in the
configuration space
2. Using the serial disable mask using the GPIO pins and
MSK_IN
3. Terminating them electrically.
In asynchronous mode, S_CLKOUT[5:0] are derived
from MSK_IN / ASYNC_CLKIN (please see CFG66 /
SCAN_EN_H / CLK_RATE pin description).
2.2.4
MISCELLANEOUS SIGNALS
Name
Pin #
Type
Description
MSK_IN /
ASYNC_CLKIN
126
K15
I
This is a multiplexed pin that is MSK_IN in
synchronous mode and ASYNC_CLK_IN in
asynchronous mode. This pin has a weak internal pull-
down resistor.
MSK_IN - Secondary Clock Disable Serial Input
(synchronous mode): This pin is used by PI7C8150B to
disable secondary clock outputs. The serial stream is
received by MSK_IN, starting when P_RESET is
detected deasserted and S_RESET_L is detected as
being asserted. The serial data is used for selectively
disabling secondary clock outputs and is shifted into the
secondary clock control configuration register. This pin
can be tied LOW to enable all secondary clock outputs
or tied HIGH to drive all the secondary clock outputs
HIGH.
ASYNC_CLKIN – Secondary Clock Input
(asynchronous mode): The asynchronous clock for the
secondary interface should be connected to this pin in
asynchronous mode. S_CLKOUT[9:0] will be derived
from ASYNC_CLKIN.
P_VIO
124
K14
I
Primary I/O Voltage: This pin is used to determine
either 3.3V or 5V signaling on the primary bus. P_VIO
must be tied to 3.3V only when all devices on the
primary bus use 3.3V signaling. Otherwise, P_VIO is
tied to 5V.
S_VIO
135
G14
I
Secondary I/O Voltage: This pin is used to determine
either 3.3V or 5V signaling on the secondary bus.
S_VIO must be tied to 3.3V only when all devices on
the secondary bus use 3.3V signaling. Otherwise, S_VIO
is tied to 5V.
BPCCE
44
N2
I
Bus/Power Clock Control Management Pin: When
this pin is tied HIGH and the PI7C8150B is placed in the
D3HOT power state, it enables the PI7C8150B to place
the secondary bus in the B2 power state. The secondary
clocks are disabled and driven to 0. When this pin is tied
LOW, there is no effect on the secondary bus clocks
when the PI7C8150B enters the D3HOT power state.
相关PDF资料 |
PDF描述 |
|---|---|
| V300A15E500B3 | CONVERTER MOD DC/DC 15V 500W |
| DSPIC33FJ64MC202-E/MM | IC DSPIC MCU/DSP 64K 28-QFN |
| PI7C8150AMAE | IC PCI-PCI BRIDGE 2PORT 208-FQFP |
| PIC18F2515-I/SP | IC MCU FLASH 24KX16 28-DIP |
| V300A15E500B2 | CONVERTER MOD DC/DC 15V 500W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI7C8150BNDI | 功能描述:外围驱动器与原件 - PCI 2-Port 32-Bit PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8150BNDI-33 | 制造商:PERICOM 制造商全称:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BNDIE | 功能描述:外围驱动器与原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8150BNDIE-33 | 功能描述:外围驱动器与原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8150DMAE | 功能描述:外围驱动器与原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。