- 您现在的位置：买卖IC网 > PDF目录11744 > PI7C8150BNDE (Pericom)IC PCI-PCI BRIDGE ASYNC 256-PBGA PDF资料下载
参数资料
| 型号： | PI7C8150BNDE |
| 厂商： | Pericom |
| 文件页数： | 28/109页 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 256-PBGA |
| 标准包装： | 90 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 256-BGA |
| 供应商设备封装： | 256-PBGA（17x17） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 25 of 109
April 2009 – Revision 1.08
Section 3.8.3.2 provides detailed information about how PI7C8150B responds to target
termination during posted write transactions.
3.5.2
MEMORY WRITE AND INVALIDATE
Posted write forwarding is used for Memory Write and Invalidate transactions.
If offset 74h bits [8:7] = 11, the PI7C8150B disconnects Memory Write and Invalidate
commands at aligned cache line boundaries. The cache line size value in the cache line size
register gives the number of DWORD in a cache line.
If offset 74h bits [8:7] = 00, the PI7C8150b converts Memory Write and Invalidate
transactions to Memory Write transactions at the destination.
If the value in the cache line size register does meet the memory write and invalidate
conditions, the PI7C8150B returns a target disconnect to the initiator on a cache line
boundary.
3.5.3
DELAYED WRITE TRANSACTIONS
Delayed write forwarding is used for I/O write transactions and Type 1 configuration write
transactions.
A delayed write transaction guarantees that the actual target response is returned back to
the initiator without holding the initiating bus in wait states. A delayed write transaction is
limited to a single DWORD data transfer.
When a write transaction is first detected on the initiator bus, and PI7C8150B forwards it
as a delayed transaction, PI7C8150B claims the access by asserting DEVSEL_L and
returns a target retry to the initiator. During the address phase, PI7C8150B samples the bus
command, address, and address parity one cycle later. After IRDY_L is asserted,
PI7C8150B also samples the first data DWORD, byte enable bits, and data parity. This
information is placed into the delayed transaction queue. The transaction is queued only if
no other existing delayed transactions have the same address and command, and if the
delayed transaction queue is not full. When the delayed write transaction moves to the head
of the delayed transaction queue and all ordering constraints with posted data are satisfied.
The PI7C8150B initiates the transaction on the target bus. PI7C8150B transfers the write
data to the target. If PI7C8150B receives a target retry in response to the write transaction
on the target bus, it continues to repeat the write transaction until the data transfer is
completed, or until an error condition is encountered.
If PI7C8150B is unable to deliver write data after 2
24 (default) or 232 (maximum) attempts,
PI7C8150B will report a system error. PI7C8150B also asserts P_SERR_L if the primary
SERR_L enable bit is set in the command register. See Section 6.4 for information on the
assertion of P_SERR_L. When the initiator repeats the same write transaction (same
command, address, byte enable bits, and data), and the completed delayed transaction is at
the head of the queue, the PI7C8150B claims the access by asserting DEVSEL_L and
returns TRDY_L to the initiator, to indicate that the write data was transferred. If the
initiator requests multiple DWORD, PI7C8150B also asserts STOP_L in conjunction with
TRDY_L to signal a target disconnect. Note that only those bytes of write data with valid
相关PDF资料 |
PDF描述 |
|---|---|
| V300A15E500B3 | CONVERTER MOD DC/DC 15V 500W |
| DSPIC33FJ64MC202-E/MM | IC DSPIC MCU/DSP 64K 28-QFN |
| PI7C8150AMAE | IC PCI-PCI BRIDGE 2PORT 208-FQFP |
| PIC18F2515-I/SP | IC MCU FLASH 24KX16 28-DIP |
| V300A15E500B2 | CONVERTER MOD DC/DC 15V 500W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI7C8150BNDI | 功能描述:外围驱动器与原件 - PCI 2-Port 32-Bit PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8150BNDI-33 | 制造商:PERICOM 制造商全称:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BNDIE | 功能描述:外围驱动器与原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8150BNDIE-33 | 功能描述:外围驱动器与原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8150DMAE | 功能描述:外围驱动器与原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。