- 您现在的位置：买卖IC网 > PDF目录370013 > PowerPC 405GP (IBM Microeletronics) 32-bit RISC Embedded Controllers(32位RISC结构嵌入式控制器) PDF资料下载
参数资料
| 型号： | PowerPC 405GP |
| 厂商： | IBM Microeletronics |
| 英文描述： | 32-bit RISC Embedded Controllers(32位RISC结构嵌入式控制器) |
| 中文描述： | 32位RISC嵌入式控制器（32位的RISC结构嵌入式控制器） |
| 文件页数： | 34/58页 |
| 文件大小： | 878K |
| 代理商： | POWERPC 405GP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
PowerPC 405GP Embedded Processor Data Sheet
34
PCIStop
The target of the current PCI transaction can assert PCIStop to
indicate to the requesting PCI master that it wants to end the
current transaction.
I/O
5V tolerant
3.3V PCI
4
PCIDevSel
PCIDevSel is driven by the target of the current PCI transaction. A
PCI target asserts PCIDevSel when it has decoded an address
and command encoding and claims the transaction.
I/O
5V tolerant
3.3V PCI
4
PCIIDSel
PCIIDSel is used during configuration cycles to select the PCI
slave interface for configuration
I
5V tolerant
3.3V PCI Rcvr
5
PCISErr
PCISErr is used for reporting address parity errors or catastrophic
failures detected by a PCI target.
I/O
5V tolerant
3.3V PCI
4
PCIPErr
PCIPErr is used for reporting data parity errors on PCI
transactions. PCIPErr is driven active by the device receiving
PCIAD0:31, PCIC0:3[BE0:3], and PCIParity, two PCI clocks
following the data in which bad parity is detected.
I/O
5V tolerant
3.3V PCI
4
PCIClk
PCIClk is used as the asynchronous PCI clock when in asynch
mode. It is unused when the PCI interface is operated
synchronously with the PLB bus.
I
5V tolerant
3.3V PCI Rcvr
5
PCIReset
PCI specific reset
O
5V tolerant
3.3V PCI
PCIINT[PerWE]
PCI interrupt. Open-drain output (two states; 0 or open circuit)
or
Peripheral write enable. Logical AND of the four PerWBE0:3 write
byte enables
O
5V tolerant
3.3V PCI
PCIReq0[Gnt]
Multipurpose signal, used as PCIReq0 when internal arbiter is
used, and as Gnt when external arbiter is used.
I
5V tolerant
3.3V PCI Rcvr
4
PCIReq1
PCIReq2
PCIReq3
PCIReq4
PCIReq5
Used as PCIReq1:5 input when internal arbiter is used
I
5V tolerant
3.3V PCI Rcvr
4
PCIGnt0[Req]
Gnt0 when internal arbiter is used
or
Req when external arbiter is used
O
5V tolerant
3.3V PCI
PCIGnt1
PCIGnt2
PCIGnt3
PCIGnt4
PCIGnt5
Used as PCIGnt1:5 output when internal arbiter is used.
O
5V tolerant
3.3V PCI
Signal Functional Description
(Part 2 of 12)
Multiplexed signals are shown in brackets following the first signal name assigned to each multiplexed ball.
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3k
to 3.3V, 10k
to 5V
)
3. Must pull down (recommended value is 1k
)
4. If not used, must pull up (recommended value is 3k
to 3.3V)
5. If not used, must pull down (recommended value is 1k
)
6. Strapping input during reset; pull-up or pull-down required
Signal Name
Description
I/O
Type
Notes
相关PDF资料 |
PDF描述 |
|---|---|
| PowerPC 440 | 32-bit RISC PowerPC Embedded Processor Cores(32位 RISC PowerPC 嵌入式处理器) |
| PowerPC 602 | 32-bit implementation Reduced Instruction Set Computer (RISC) Microprocessors.(32位精简指令集微处理器) |
| PowerPC 603e | 32-Bit PowerPC Reduced Instruction Set Computer (RISC) Microprocessor(32-位 PowerPC 精简指令集微处理器) |
| PowerPC EM603e | 32-Bit PowerPC Reduced Instruction Set Computer (RISC) Microprocessor(32-位 PowerPC 精简指令集微处理器) |
| PowerPC 740 | 32-Bit Embedded Microprocessor(32位精简指令集嵌入式微处理器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| POWERPLUG15W | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:AC/DC POWER SUPPLY |
| POWERPLUG24W | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:AC/DC POWER SUPPLY |
| POWERPLUS 2C 2500MAH | 制造商:Energizer Battery Company 功能描述: |
| POWERPLUS 2D 2500MAH | 制造商:Energizer Battery Company 功能描述: |
| POWERPLUS 4AAA 850MAH | 制造商:Energizer Battery Company 功能描述: |
发布紧急采购，3分钟左右您将得到回复。