- 您现在的位置：买卖IC网 > PDF目录192299 > S29GL032M10TAIR52 (Spansion Inc.) CAP TANT 220UF 2.5V 20% POLY SMD PDF资料下载
参数资料
| 型号： | S29GL032M10TAIR52 |
| 厂商： | Spansion Inc. |
| 英文描述： | CAP TANT 220UF 2.5V 20% POLY SMD |
| 中文描述： | MirrorBit闪存系列 |
| 文件页数： | 158/159页 |
| 文件大小： | 5216K |
| 代理商： | S29GL032M10TAIR52 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页当前第158页第159页
98
S29GLxxxM MirrorBitTM Flash Family
S29GLxxxM_00_B3 Octorber 18, 2004
Data s he et
Factory Locked: SecSi Sector Programmed and Protected At the Factory
In devices with an ESN, the SecSi Sector is protected when the device is shipped from the factory. The SecSi Sec-
tor cannot be modified in any way. An ESN Factory Locked device has an 16-byte random ESN at addresses
000000h–000007h. Please contact your sales representative for details on ordering ESN Factory Locked devices.
Customers may opt to have their code programmed by the factory through the Spansion programming service
(Customer Factory Locked). The devices are then shipped from the factory with the SecSi Sector permanently
locked. Contact your sales representative for details on using the Spansion programming service.
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting the first or last sector group without using
VID. Write Protect is one of two functions provided by the WP#/ACC input.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the first or last
sector group independently of whether those sector groups were protected or unprotected. Note that if WP#/ACC
is at VIL when the device is in the standby mode, the maximum input load current is increased. See Table 22 on
Note: If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was
previously set to be protected or unprotected using the method described in “Sector Group Protection and
Unprotection”. Note that WP# has an internal pullup; when unconnected, WP# is at VIH.
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing provides data protection
against inadvertent writes (refer to Table 35 on page 113 and Table 36 on page 114 for command definitions). In
addition, the following hardware data protection measures prevent accidental erasure or programming, which
might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or
from system noise.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up
and power-down. The command register and all internal program/erase circuits are disabled, and the device re-
sets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide
the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO.
Write Pulse “Glitch” Protection
Noise pulses of less than 3 ns (typical) on OE#, CE# or WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a logical one.
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge
of WE#. The internal state machine is automatically reset to the read mode on power-up.
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL032M10TAIR53 | CAP TANT 330UF 2.5V 20% POLY SMD |
| S29GL032M10TAIR60 | CAP TANT 470UF 4V 20% POLY SMD |
| S29GL032M10TAIR62 | CAP TANT 470UF 4V 20% POLY SMD |
| S29GL032M10TCCR22 | MirrorBit Flash Family |
| S29GL032M10TCCR23 | MirrorBit Flash Family |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL032M10TAIR53 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TAIR60 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TAIR62 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TAIR63 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TBCR00 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
发布紧急采购，3分钟左右您将得到回复。