- 您现在的位置：买卖IC网 > PDF目录225141 > S29GL256N80FAI010 (SPANSION LLC) MirrorBit Flash Family PDF资料下载
参数资料
| 型号： | S29GL256N80FAI010 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | 16M X 16 FLASH 3V PROM, 80 ns, PBGA64 |
| 封装： | 13 X 11 MM, 1MM PITCH, FBGA-64 |
| 文件页数： | 65/110页 |
| 文件大小： | 2624K |
| 代理商： | S29GL256N80FAI010 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页当前第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
58
S29GLxxxN MirrorBitTM Flash Family
27631A4 May 13, 2004
Adva nce
Inform at i o n
Reading Array Data
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data. The device is ready to read array data
after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the
erase-suspend-read mode, after which the system can read data from any non-
erase-suspended sector. After completing a programming operation in the Erase
Suspend mode, the system may once again read array data with the same ex-
ception. See the Erase Suspend/Erase Resume Commands section for more
information.
The system must issue the reset command to return the device to the read (or
erase-suspend-read) mode if DQ5 goes high during an active program or erase
operation, or if the device is in the autoselect mode. See the next section, Reset
Command, for more information.
See also Requirements for Reading Array Data in the Device Bus Operations sec-
tion for more information. The Read-Only Operations–“AC Characteristics”
section on page 88 provides the read parameters, and Figure 11 shows the timing
diagram.
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read
mode. Address bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the device to the read
mode. Once erasure begins, however, the device ignores reset commands until
the operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins. This resets the device to the
read mode. If the program command sequence is written while the device is in
the Erase Suspend mode, writing the reset command returns the device to the
erase-suspend-read mode. Once programming begins, however, the device ig-
nores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command must be
written to return to the read mode. If the device entered the autoselect mode
while in the Erase Suspend mode, writing the reset command returns the device
to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command
returns the device to the read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the sys-
tem must write the Write-to-Buffer-Abort Reset command sequence to reset the
device for the next operation.
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
an alternative to that shown in Table 5, which is intended for PROM programmers
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL256N80FFI010 | MirrorBit Flash Family |
| S29GL256N80FFI013 | MirrorBit Flash Family |
| S29JL032H90TAI223 | 2M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| S29WS064N0PBAW011 | 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY |
| S29WS128N0LBFI111 | 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL256N90FFIR10 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 64-Pin Fortified BGA Tray |
| S29GL256N90FFIR22 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR10 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 256Mbit 32M/16M x 8bit/16bit 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL256N90TFIR2 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR20 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
发布紧急采购，3分钟左右您将得到回复。