参数资料
型号: SAB-C515-LM
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80
封装: PLASTIC, MQFP-80
文件页数: 42/162页
文件大小: 771K
代理商: SAB-C515-LM
Semiconductor Group
9-5
Power Saving Modes
C515
9.4
Slow Down Mode Operation (C515-LM/1RM only)
In some applications, where power consumption and dissipation are critical, the controller might run
for a certain time at reduced speed (e.g. if the controller is waiting for an input signal). Since in
CMOS devices there is an almost linear dependence of the operating frequency and the power
supply current, a reduction of the operating frequency results in reduced power consumption.
In the slow down mode all signal frequencies that are derived from the oscillator clock are divided
by 8.
The slow down mode is activated by setting the bit SD in SFR PCON. If the slow down mode is
enabled, the clock signals for the CPU and the peripheral units are reduced to 1/8 of the nominal
system clock rate. The controller actually enters the slow down mode after a short synchronization
period (max. two machine cycles). The slow down mode is terminated by clearing bit SD.
The slow down mode can be combined with the idle mode by performing the following double
instruction sequence:
ORL
PCON,#00000001B
; preparing idle mode: set bit IDLE (IDLS not set)
ORL
PCON,#00110000B
; entering idle mode combined with the slow down mode:
; (IDLS and SD set)
There are two ways to terminate the combined Idle and Slow Down Mode :
– The idle mode can be terminated by activation of any enabled interrupt. The CPU operation
is resumed, the interrupt will be serviced and the next instruction to be executed after the RETI
instruction will be the one following the instruction that had set the bits IDLS and SD.
Nevertheless the slow down mode keeps enabled and if required has to be terminated by
clearing the bit SD in the corresponding interrupt service routine or at any point in the program
where the user no longer requires the slow-down mode power saving.
– The other possibility of terminating the combined idle and slow down mode is a hardware
reset. Since the oscillator is still running, the hardware reset has to be held active for only two
machine cycles for a complete reset.
The slow down feature is not available for C515-LN/1RN versions.
相关PDF资料
PDF描述
SAB-C515C-LM 8-BIT, 10 MHz, MICROCONTROLLER, PQFP80
SAB-XC164CM-8F40F 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64
SAB-XC164CM-4F40F 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64
SAB-XC164CM-8F20F 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64
SAB-XC164KM-4F40F 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
SAB-C517A 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-bit CMOS MICROCONTROLLER
SAB-C517A-4R24M 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller
SAB-C517A-4RM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller
SAB-C517A-L24M 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller
SAB-C517A-LM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller