参数资料
| 型号： | SC16C852VIET,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 27/55页 |
| 文件大小： | 0K |
| 描述： | IC UART DUAL W/FIFO 36TFBGA |
| 标准包装： | 490 |
| 特点： | 可编程 |
| 通道数： | 2，DUART |
| FIFO's： | 128 字节 |
| 规程： | RS485 |
| 电源电压： | 2.5V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-TFBGA |
| 供应商设备封装： | 36-TFBGA（3.5x3.5） |
| 包装： | 托盘 |
| 其它名称： | 568-5662 935282518151 SC16C852VIET,151-ND SC16C852VIET-S SC16C852VIET-S-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
SC16C852V
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 21 January 2011
33 of 55
NXP Semiconductors
SC16C852V
Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
7.14 Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register.
Bit 0 through bit 4 provide single or dual character software flow control selection. When
the Xon1 and Xon2 and/or Xoff1 and Xoff2 modes are selected, the double 8-bit words are
concatenated into two sequential numbers.
[1]
Enhanced function control bits: IER[7:4], ISR[5:4], FCR[5:4] and MCR[7:5].
Table 25.
Enhanced Feature Register bits description
Bit
Symbol
Description
7
EFR[7]
Automatic CTS flow control.
logic 0 = automatic CTS flow control is disabled (normal default condition)
logic 1 = enable automatic CTS flow control. Transmission will stop when
CTS goes to a logical 1. Transmission will resume when the CTS signal
returns to a logical 0.
6
EFR[6]
Automatic RTS flow control. Automatic RTS may be used for hardware flow
control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will be
generated when the receive FIFO is filled to the programmed trigger level and
RTS will go to a logic 1 at the next trigger level. RTS will return to a logic 0 when
data is unloaded below the next lower trigger level (programmed trigger level 1).
The state of this register bit changes with the status of the hardware flow
control. RTS functions normally when hardware flow control is disabled.
logic 0 = automatic RTS flow control is disabled (normal default condition)
logic 1 = enable automatic RTS flow control
5
EFR[5]
Special character detect.
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. The SC16C852V compares each
incoming receive character with Xoff2 data. If a match exists, the received
data will be transferred to FIFO and ISR[4] will be set to indicate detection of
special character. Bit-0 in the X-registers corresponds with the LSB bit for the
receive character. When this feature is enabled, the normal software flow
control must be disabled (EFR[3:0] must be set to a logic 0).
4
EFR[4]
Enhanced function control bit. The content of IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] can be modified and latched. After modifying any bits in the enhanced
registers, EFR[4] can be set to a logic 0 to latch the new values. This feature
prevents existing software from altering or overwriting the SC16C852V
enhanced functions.
logic 0 = disable/latch enhanced features[1]
logic 1 = enables the enhanced functions[1]. When this bit is set to a logic 1,
all enhanced features of the SC16C852V are enabled and user settings
stored during a reset will be restored.
3:0
EFR[3:0]
Cont-3:0 Tx, Rx control. Logic 0 or cleared is the default condition.
Combinations of software flow control can be selected by programming these
bits. See Table 26.
Table 26.
Software flow control functions[1]
Cont-3
Cont-2
Cont-1
Cont-0
TX, RX software flow controls
0
X
No transmit flow control
1
0
X
Transmit Xon1/Xoff1
0
1
X
Transmit Xon2/Xoff2
相关PDF资料 |
PDF描述 |
|---|---|
| SC16IS741IPW,112 | IC UART 16TSSOP |
| SC16IS750IBS,151 | IC UART I2C/SPI 24-HVQFN |
| SC16IS762IBS,151 | IC UART DUAL I2C/SPI 32-HVQFN |
| SC26C92A1N,112 | IC UART 40-DIP |
| SC28C94A1A,512 | IC UART QUAD W/FIFO 52-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C852VIET-G | 功能描述:UART 接口集成电路 1.8V 2CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C852VIET-S | 功能描述:UART 接口集成电路 1.8V 2CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16DP-26 | 制造商:Thomas & Betts 功能描述:SAXXIT CABLE CLIP W/ DRIVE PIN -7 制造商:Belden Inc 功能描述: |
| SC16DP-3Q | 制造商:Thomas & Betts 功能描述:SAXXIT CABLE CLIP W/ DRIVE PIN -8 |
| SC16-FM-M16-NPB-ML-1 | 制造商:HellermannTyton 功能描述: |
发布紧急采购，3分钟左右您将得到回复。