参数资料
| 型号： | SC2446ITETRT |
| 厂商： | Semtech |
| 文件页数： | 10/38页 |
| 文件大小： | 0K |
| 描述： | IC SYNC STEP DOWN CTRLR 28-TSSOP |
| 标准包装： | 1 |
| 应用： | 控制器，DDR |
| 输入电压： | 4.7 V ~ 16 V |
| 输出数： | 2 |
| 输出电压： | 可调至 0.5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC2446ITEDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
SC2446
POWER MANAGEMENT
Operation (Cont.)
unloaded versions of their respective power phase
voltages) for current sensing. This method does not
require any precision sense resistor. It is cheaper to
implement but is less accurate than resistor current
sensing. Since the sensed voltage is developed at the
output of the step-down converter, it is less prone to
switching transient spikes. This method will be described
in more details in the Applications Information section.
Error Amplifiers
In closed loop operation, the error amplifier output ranges
from 1.1V to 3.5V. The upper output operating range of
either error amplifier is reserved for positive current-
sense voltage (CS+ - CS-) and corresponds to positive
(sourcing) output current. If the amplifier swings to its
lower operating range, the amplifier will still modulate
the high-side gate drive duty-ratio. However the peak
current-sense voltage (hence the peak inductor current)
will be limited to a negative value. The error amplifier
output is about 2.2V when the peak sense-voltage is zero.
The built-in offset in the current sense amplifier together
with synchronous continuous-conduction mode of
operation allows the SC2446 to regulate the output
irrespective of the direction of the load current.
The non-inverting input of the first feedback amplifier is
tied to the internal 0.5V voltage reference. Both the non-
inverting and the inverting inputs of the second error
amplifier are brought out as device pins so that the output
of the second converter can be made to track the output
of the first channel. For example in DDR applications,
Channel 1 can be used to generate V DDQ (2.5V) from the
input (5V or 12V) and channel 2 is used to produce a
tracking V TT (1.25V) with V DDQ being its input.
Current-Limit
The maximum current sense voltage of +75mV is the
cycle-by-cycle peak current limit when the load is drawing
current from the converter. There is no cycle-by-cycle
current limiting when the inductor current flows in the
negative direction. However once the valley of the current
sense voltage exceeds –110mV, the corresponding
channel will undergo shutdown and restart (hiccup).
Soft-Start and Overload Protection
The undervoltage lockout circuit discharges the SS/EN
capacitors. After V CC rises above 4.5V, the SS/EN capacitors
are slowly charged by internal 2 μ A current source. With
internal PNP transistors, the SS/EN voltages clamp the
error amplifier outputs. When the error amplifier output
rises to 2.2V, the high-side MOSFET starts to switch. As
the SS/EN capacitor continues to be charged, the COMP
voltage follows. The converter gradually delivers increasing
power to the output. The inductor current follows the COMP
voltage envelope until the output goes into regulation. The
SS/EN clamp on COMP is then released.
After the SS/EN capacitor is charged above 3.2V (high
enough for the error amplifier to provide full load current),
the overload detection circuit is activated. If the output
voltage falls below 70% of its set value or the valley
current-sense voltage exceeds –110mV, an overload latch
will be set and both the top and the bottom MOSFETs will
be turned off. The SS/EN capacitor is slowly discharged
with an internal 1.4 μ A current sink. The overload latch is
reset when the SS/EN capacitor is discharged below 0.5V.
The SS/EN capacitor is then recharged with the 2 μ A current
source and the converter undergoes soft-start. If overload
persists, the SC2446 will undergo repetitive shutdown and
restart (Figure 3).
If the output is short-circuited, the inductor current will
not increase indefinitely between the time the inductor
current reaching its current limit and the instant the
converter shuts down. This is due to cycle skipping
reduces the actual operating frequency.
The SS/EN pin can also be used as the enable input for
that channel. Both the high-side and the low-side
MOSFETs will be turned off if the SS/EN pin is pulled
below 0.7V.
? 2004 Semtech Corp.
10
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC2544TSTRT | IC REG CTRLR BUCK PWM VM 24TSSOP |
| SC2595MLTRT | IC DDR TERMINATION REG 16-MLPQ |
| SC2596STRT | IC INTEGRTD DDRII TERM REG 8SOIC |
| SC2608BSTRT | IC REG CTRLR BUCK PWM VM 8-SOIC |
| SC283WLTRT | IC REG BUCK SYNC ADJ 1.8A 18MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC2446ITSTRT | 制造商:Semtech Corporation 功能描述:Controller IC 制造商:Semtech Corporation 功能描述:SC Series 4.7 to 16 V 1 MHz Dual-Phase Synchronous Step-Down Controller TSSOP-28 |
| SC2447 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase, Single or Dual Output Synchronous Step-Down Controller |
| SC24-470-R | 功能描述:INDUCTOR SHIELD 47UH 150MA SMD RoHS:是 类别:电感器，线圈，扼流圈 >> 固定式 系列:SC24 标准包装:500 系列:1331 电感:1.2µH 电流:247mA 电流 - 饱和:247mA 电流 - 温升:- 类型:铁芯体 容差:±10% 屏蔽:屏蔽 DC 电阻(DCR):最大 730 毫欧 Q因子@频率:40 @ 7.9MHz 频率 - 自谐振:130MHz 材料 - 芯体:铁 封装/外壳:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安装类型:表面贴装 包装:带卷 (TR) 工作温度:-55°C ~ 105°C 频率 - 测试:7.9MHz |
| SC24-471-R | 功能描述:INDUCTOR SHIELD 470UH 50MA SMD RoHS:是 类别:电感器，线圈，扼流圈 >> 固定式 系列:SC24 标准包装:500 系列:1331 电感:1.2µH 电流:247mA 电流 - 饱和:247mA 电流 - 温升:- 类型:铁芯体 容差:±10% 屏蔽:屏蔽 DC 电阻(DCR):最大 730 毫欧 Q因子@频率:40 @ 7.9MHz 频率 - 自谐振:130MHz 材料 - 芯体:铁 封装/外壳:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安装类型:表面贴装 包装:带卷 (TR) 工作温度:-55°C ~ 105°C 频率 - 测试:7.9MHz |
| SC2447EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase, Single or Dual Output Synchronous Step-Down Controller |
发布紧急采购，3分钟左右您将得到回复。