参数资料
| 型号： | SC2446ITETRT |
| 厂商： | Semtech |
| 文件页数： | 11/38页 |
| 文件大小： | 0K |
| 描述： | IC SYNC STEP DOWN CTRLR 28-TSSOP |
| 标准包装： | 1 |
| 应用： | 控制器，DDR |
| 输入电压： | 4.7 V ~ 16 V |
| 输出数： | 2 |
| 输出电压： | 可调至 0.5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC2446ITEDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
SC2446
POWER MANAGEMENT
Application Information
SC2446 consists of two current-mode synchronous buck
controllers with many integrated functions. By proper
application circuitry configuration, SC2446 can be used
to generate
1) two independent outputs from a common input or two
different inputs or
1)
2)
3)
4)
5)
Passive component size
Circuitry efficiency
EMI condition
Minimum switch on time and
Maximum duty ratio
2) dual phase output with current sharing,
3) current sourcing/sinking from common or separate
inputs as in DDR (I and II) memory application.
The application information related to the converter design
using SC2446 is described in the following.
Step-down Converter
For a given output power, the sizes of the passive
components are inversely proportional to the switching
frequency, whereas MOSFET’s/Diodes switching losses are
proportional to the operating frequency. Other issues such
as heat dissipation, packaging and the cost issues are
also to be considered. The frequency bands for signal
transmission should be avoided because of EM
interference.
Starting from the following step-down converter
specifications,
Input voltage range: V in ∈ [ V in , min , V in , max ]
Input voltage ripple (peak-to-peak): ? V in
Output voltage: V o
Output voltage accuracy: ε
Output voltage ripple (peak-to-peak): ? V o
Nominal output (load) current: I o
Maximum output current limit: I o,max
Output (load) current transient slew rate: dI o (A/s)
Circuit efficiency: η
Selection criteria and design procedures for the following
are described.
1) output inductor ( L ) type and value,
2) output capacitor ( C o ) type and value,
3) input capacitor ( C in ) type and value,
4) power MOSFET’s,
5) current sensing and limiting circuit,
6) voltage sensing circuit,
7) loop compensation network.
Operating Frequency (f s )
The switching frequency in the SC2446 is user-
programmable. The advantages of using constant
frequency operation are simple passive component
selection and ease of feedback compensation. Before
setting the operating frequency, the following trade-offs
should be considered.
Minimum Switch On Time Consideration
In the SC2446 the falling edge of the clock turns on the
top MOSFET. The inductor current and the sensed voltage
ramp up. After the sensed voltage crosses a threshold
determined by the error amplifier output, the top MOSFET
is turned off. The propagation delay time from the turn-
on of the controlling FET to its turn-off is the minimum
switch on time. The SC2446 has a minimum on time of
about 150ns at room temperature. This is the shortest
on interval of the controlling FET. The controller either does
not turn on the top MOSFET at all or turns it on for at least
150ns.
For a synchronous step-down converter, the operating duty
cycle is V O /V IN . So the required on time for the top MOSFET
is V O /(V IN fs). If the frequency is set such that the required
pulse width is less than 150ns, then the converter will
start skipping cycles. Due to minimum on time limitation,
simultaneously operating at very high switching frequency
and very short duty cycle is not practical. If the voltage
conversion ratio V O /V IN and hence the required duty cycle
is higher, the switching frequency can be increased to reduce
the sizes of passive components.
There will not be enough modulation headroom if the on
time is simply made equal to the minimum on time of the
SC2446. For ease of control, we recommend the required
pulse width to be at least 1.5 times the minimum on time.
? 2004 Semtech Corp.
11
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC2544TSTRT | IC REG CTRLR BUCK PWM VM 24TSSOP |
| SC2595MLTRT | IC DDR TERMINATION REG 16-MLPQ |
| SC2596STRT | IC INTEGRTD DDRII TERM REG 8SOIC |
| SC2608BSTRT | IC REG CTRLR BUCK PWM VM 8-SOIC |
| SC283WLTRT | IC REG BUCK SYNC ADJ 1.8A 18MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC2446ITSTRT | 制造商:Semtech Corporation 功能描述:Controller IC 制造商:Semtech Corporation 功能描述:SC Series 4.7 to 16 V 1 MHz Dual-Phase Synchronous Step-Down Controller TSSOP-28 |
| SC2447 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase, Single or Dual Output Synchronous Step-Down Controller |
| SC24-470-R | 功能描述:INDUCTOR SHIELD 47UH 150MA SMD RoHS:是 类别:电感器，线圈，扼流圈 >> 固定式 系列:SC24 标准包装:500 系列:1331 电感:1.2µH 电流:247mA 电流 - 饱和:247mA 电流 - 温升:- 类型:铁芯体 容差:±10% 屏蔽:屏蔽 DC 电阻(DCR):最大 730 毫欧 Q因子@频率:40 @ 7.9MHz 频率 - 自谐振:130MHz 材料 - 芯体:铁 封装/外壳:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安装类型:表面贴装 包装:带卷 (TR) 工作温度:-55°C ~ 105°C 频率 - 测试:7.9MHz |
| SC24-471-R | 功能描述:INDUCTOR SHIELD 470UH 50MA SMD RoHS:是 类别:电感器，线圈，扼流圈 >> 固定式 系列:SC24 标准包装:500 系列:1331 电感:1.2µH 电流:247mA 电流 - 饱和:247mA 电流 - 温升:- 类型:铁芯体 容差:±10% 屏蔽:屏蔽 DC 电阻(DCR):最大 730 毫欧 Q因子@频率:40 @ 7.9MHz 频率 - 自谐振:130MHz 材料 - 芯体:铁 封装/外壳:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安装类型:表面贴装 包装:带卷 (TR) 工作温度:-55°C ~ 105°C 频率 - 测试:7.9MHz |
| SC2447EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase, Single or Dual Output Synchronous Step-Down Controller |
发布紧急采购，3分钟左右您将得到回复。