参数资料
| 型号： | SC2446ITETRT |
| 厂商： | Semtech |
| 文件页数： | 25/38页 |
| 文件大小： | 0K |
| 描述： | IC SYNC STEP DOWN CTRLR 28-TSSOP |
| 标准包装： | 1 |
| 应用： | 控制器，DDR |
| 输入电压： | 4.7 V ~ 16 V |
| 输出数： | 2 |
| 输出电压： | 可调至 0.5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC2446ITEDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
SC2446
POWER MANAGEMENT
Application Information (Cont.)
In some initial prototypes, if the circuit noise makes the
control loop jittering, it is suggested to use a bigger C 3
value than the calculated one here. Effectively, the
converter bandwidth is reduced in order to reject some
high frequency noises. In the final working circuit, the
loop transfer function should be measured using network
analyzer and compared with the design to ensure circuit
stability under different line and load conditions. The load
transient response behavior is further tested and
measured to meet the specification.
PC Board Layout Issues
Circuit board layout is very important for the proper
operation of high frequency switching power converters. A
power ground plane is required to reduce ground bounces.
The followings are suggested for proper layout.
Power Stage
1) Separate the power ground from the signal ground. In
SC2446, the power ground PGND should be tied to the
source terminal of lower MOSFETs. The signal ground
AGND should be tied to the negative terminal of the
output capacitor.
2) Minimize the size of high pulse current loop. Keep the
top MOSFET, bottom MOSFET and the input capacitors
within a small area with short and wide traces. In addition
to the aluminum energy storage capacitors, add multi-
layer ceramic (MLC) capacitors from the input to the power
ground to improve high frequency bypass.
3) Reduce high frequency voltage ringing. Widen and
shorten the drain and source traces of the MOSFET’s to
reduce stray inductances. Add a small RC snubber if
necessary to reduce the high frequency ringing at the phase
node. Sometimes slowing down the gate drive signal also
helps in reducing the high frequency ringing at the phase
node.
4) Shorten the gate driver path. Integrity of the gate drive
(voltage level, leading and falling edges) is important for
circuit operation and efficiency. Short and wide gate drive
traces reduce trace inductances. Bond wire inductance
is about 2~3nH. If the length of the PCB trace from the
gate driver to the MOSFET gate is 1 inch, the trace
inductance will be about 25nH. If the gate drive current
is 2A with 10ns rise and falling times, the voltage drops
across the bond wire and the PCB trace will be 0.6V and
5V respectively. This may slow down the switching
transient of the MOSFET’s. These inductances may also
ring with the gate capacitance.
5) Put the decoupling capacitor for the gate drive power
supplies (BST and PVCC) close to the IC and power
ground.
Control Section
6) The frequency-setting resistor Rosc should be placed
close to Pin 3. Trace length from this resistor to the analog
ground should be minimized.
7) Solder the bias decoupling capacitor right across the
AVCC and analog ground AGND.
8) Place the Combi-sense components away from the
power circuit and close to the corresponding CS+ and CS-
pins. Use X7R type ceramic capacitor for the Combi-sense
capacitor because of their temperature stability.
9) Use an isolated local ground plane for the controller
and tie it to the negative side of output capacitor bank.
? 2004 Semtech Corp.
25
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC2544TSTRT | IC REG CTRLR BUCK PWM VM 24TSSOP |
| SC2595MLTRT | IC DDR TERMINATION REG 16-MLPQ |
| SC2596STRT | IC INTEGRTD DDRII TERM REG 8SOIC |
| SC2608BSTRT | IC REG CTRLR BUCK PWM VM 8-SOIC |
| SC283WLTRT | IC REG BUCK SYNC ADJ 1.8A 18MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC2446ITSTRT | 制造商:Semtech Corporation 功能描述:Controller IC 制造商:Semtech Corporation 功能描述:SC Series 4.7 to 16 V 1 MHz Dual-Phase Synchronous Step-Down Controller TSSOP-28 |
| SC2447 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase, Single or Dual Output Synchronous Step-Down Controller |
| SC24-470-R | 功能描述:INDUCTOR SHIELD 47UH 150MA SMD RoHS:是 类别:电感器，线圈，扼流圈 >> 固定式 系列:SC24 标准包装:500 系列:1331 电感:1.2µH 电流:247mA 电流 - 饱和:247mA 电流 - 温升:- 类型:铁芯体 容差:±10% 屏蔽:屏蔽 DC 电阻(DCR):最大 730 毫欧 Q因子@频率:40 @ 7.9MHz 频率 - 自谐振:130MHz 材料 - 芯体:铁 封装/外壳:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安装类型:表面贴装 包装:带卷 (TR) 工作温度:-55°C ~ 105°C 频率 - 测试:7.9MHz |
| SC24-471-R | 功能描述:INDUCTOR SHIELD 470UH 50MA SMD RoHS:是 类别:电感器，线圈，扼流圈 >> 固定式 系列:SC24 标准包装:500 系列:1331 电感:1.2µH 电流:247mA 电流 - 饱和:247mA 电流 - 温升:- 类型:铁芯体 容差:±10% 屏蔽:屏蔽 DC 电阻(DCR):最大 730 毫欧 Q因子@频率:40 @ 7.9MHz 频率 - 自谐振:130MHz 材料 - 芯体:铁 封装/外壳:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安装类型:表面贴装 包装:带卷 (TR) 工作温度:-55°C ~ 105°C 频率 - 测试:7.9MHz |
| SC2447EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase, Single or Dual Output Synchronous Step-Down Controller |
发布紧急采购，3分钟左右您将得到回复。