参数资料
| 型号： | SC2544TSTRT |
| 厂商： | Semtech |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 24TSSOP |
| 标准包装： | 1 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 300kHz |
| 占空比： | 90% |
| 电源电压： | 4.5 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC2544TSDKR |
SC2544
POWER MANAGEMENT
Tss =
Applications Information
Overview
The SC2544 is a constant frequency 2-phase voltage
mode step-down PWM switching controller driving all N-
channel MOSFETs. The two channels of the controller
operate at 180 degree out of phase from each other.
Since input currents are interleaved in a two-phase
converter, input ripple current is lower and smaller input
capacitance can be used for filtering. Also, with lower
inductor current and smaller inductor ripple current per
phase, overall I 2 R losses are reduced.
F requency Setting
The frequency of the SC2544 is user- programmable.
The oscillator of SC2544 can be programmed with an
external resistor from the Rosc pin to the ground. The
step-down controller is capable of operating up to
300KHz. The relationship between oscillation frequency
versus oscillation resistor is shown in Figure 1.
The advantages of using constant frequency operation
are simple passive component selection and ease of
feedback compensation. Before setting the operating
frequency, the following trade-offs should be considered.
1) Passive component size
2) Circuitry efficiency
3) EMI condition
4) Minimum switch on time
5) Maximum duty ratio
For a given output power, the sizes of the passive
components are inversely proportional to the switching
frequency, whereas MOSFETs/Diodes switching losses
are proportional to the operating frequency. Other issues
such as heat dissipation, packaging and cost issues are
also to be considered. The frequency bands for signal
transmission should be avoided because of EM
interference.
350
300
250
200
150
100
50
Rosc(KOHM)
Figure 1. Switching frequency versus Rosc.
Start-up
During start-up, the reference voltage of the error
amplifier equals 30% of the voltage on Css (soft-start
capacitor) which is connected between the SS pin and
ground. When the controller is enabled (by pulling EN
pin high), one internal 84uA current source, I SS, (soft
start current) will charge the soft-start capacitor
gradually. The PWM output starts pulsing when the
soft start voltage reaches 1V.
This soft start scheme will ensure the duty cycle to
increase slowly, therefore limiting the charging current
into the output capacitor and also ensuring the
inductor does not saturate. The soft start capacitor
will eventually be charged up to 2.5V.
The soft-start sequence is initiated when EN pin is high
and Vcc >4.5V or during recovery from a fault condition
( OCP, OVP, or UVLO).
The period of start up can be programed by the soft
start capacitor:
Css × 2.5 V
84 μ A
By connecting different capacitors at SS1 and SS2
pins, VO1 and VO2 will start at different time, achieving
sequential start-up for the outputs. Connecting SS1
and SS2 together would make the 2 outputs start and
reach steady state values at the same time, achieving
ratiometric start-up.
Shutdown
When the EN pin is pulled low, an internal 15uA current
source discharges the soft-start capacitor and DRVH/
DRVL signals stop pulsing. The output voltage ramps
down at a rate determined by the load condition.
The SC2544 can also be shutdown by pulling down
directly on the SS pin. The designer needs to consider
the slope of the SS pin voltage and choose a suitable
pull down resistor to prevent the output from
undershooting.
Shutdown can also be triggered when an OCP condition
occurs. When an OCP condition is detected, DRVH and
DRVL will stop pulsing and enter a “tri-state shutdown”
with the output voltage ramping down at a rate deter-
mined by the load condition. The internal 15uA current
source will begin discharging the soft-start capacitor
and when the soft-start voltage reaches 0.65V, DRVL
will go high.
? 2005 Semtech Corp.
8
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC2595MLTRT | IC DDR TERMINATION REG 16-MLPQ |
| SC2596STRT | IC INTEGRTD DDRII TERM REG 8SOIC |
| SC2608BSTRT | IC REG CTRLR BUCK PWM VM 8-SOIC |
| SC283WLTRT | IC REG BUCK SYNC ADJ 1.8A 18MLPQ |
| SC286ULTRT | IC REG BUCK SYNC ADJ 4A 28MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC2545 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2545EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2545MLTRT | 制造商:Semtech Corporation 功能描述:Controller IC |
| SC2545TSTRT | 制造商:Semtech Corporation 功能描述:Controller IC 制造商:Semtech Corporation 功能描述:DC DC Cntrlr Dual-OUT Synchronous Buck Controller/PWM DC to DC Controller 4.5V to 28V Input 24-Pin TSSOP T/R |
| SC25-500VP | 制造商:JAMECO VALUEPRO 功能描述:CABLE,SHIELDED,25 CONDUCTOR,GRAY,24AWG,500 FEET,ROUND |
发布紧急采购，3分钟左右您将得到回复。