- 您现在的位置：买卖IC网 > PDF目录11820 > SCC68692E1N40,602 (NXP Semiconductors)IC DUART 40DIP PDF资料下载
参数资料
| 型号： | SCC68692E1N40,602 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC DUART 40DIP |
| 标准包装： | 9 |
| 特点： | 故障启动位检测 |
| 通道数： | 2，DUART |
| FIFO's： | 3 位 |
| 电源电压： | 5V |
| 带并行端口： | 是 |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 通孔 |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 40-DIP |
| 包装： | 管件 |
| 其它名称： | 935027050602 SCC68692E1N40 SCC68692E1N40-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Philips Semiconductors
Product data
SCC68692
Dual asynchronous receiver/transmitter (DUART)
2004 Mar 03
23
TRANSMITTER
ENABLED
TxD
ADD#1
TxRDY
(SR2)
CSN
(WRITE)
MR1(4+3) = 11
MR1(2) = 1
1
BIT 9
D0
0
BIT 9
ADD#2 1
BIT 9
MASTER STATION
ADD#1 MR1(2) = 0 D0
MR1(2) = 1 ADD#2
RxD
ADD#1 1
BIT 9
D0
0
BIT 9
ADD#2 1
BIT 9
PERIPHERAL STATION
0
BIT 9
0
BIT 9
RECEIVER
ENABLED
RxRDY
(SR0)
CSN
MR1(4:3) = 11
ADD#1
STATUS DATA
D0
STATUS DATA
ADD#2
SD00120
Figure 14. Wake-Up Mode
INTRN
D0–D7
TxDA/B
OP0–OP7
150pF
2.15V
750
50pF
+5V
2.7K
SD00151
Figure 15. Test Conditions on Outputs
Output Port Notes
The output ports are controlled from four places: the OPCR register,
the OPR register, the MR registers and the command register. The
OPCR register controls the source of the data for the output ports
OP2 through OP7. The data source for output ports OP0 and OP1 is
controlled by the MR and CR registers. When the OPR is the source
of the data for the output ports, the data at the ports is inverted from
that in the OPR register. The content of the OPR register is
controlled by the “Set Output Port Bits Command” and the “Reset
Output Bits Command”. These commands are at E and F,
respectively. When these commands are used, action takes place
only at the bit locations where ones exist. For example, a one in bit
location 5 of the data word used with the “Set Output Port Bits”
command will result in OPR5 being set to one. The OP5 would then
be set to zero (VSS). Similarly, a one in bit position 5 of the data
word associated with the “Reset Output Ports Bits” command would
set OPR5 to zero and, hence, the pin OP5 to a one (VDD).
The CTS, RTS, CTS Enable Tx signals
CTS (Clear To Send) is usually meant to be a signal to the
transmitter meaning that it may transmit data to the receiver. The
CTS input is on pin MPI. The CTS signal is active LOW; thus, it is
called CTS.
RTS is usually meant to be a signal from the receiver indicating that
the receiver is ready to receive data. It is also active LOW and is,
thus, called RTSN. RTSN is on pin MP0. A receiver’s RTS output
will usually be connected to the CTS input of the associated
transmitter. Therefore, one could say that RTS and CTS are different
ends of the same wire!
MR2(4) is the bit that allows the transmitter to be controlled by the
CTS pin (MPI). When this bit is set to one AND the CTS input is
driven HIGH, the transmitter will stop sending data at the end of the
present character being serialized. It is usually the RTS output of the
receiver that will be connected to the transmitter’s CTS input. The
receiver will set RTS HIGH when the receiver FIFO is full AND the
start bit of the fourth character is sensed. Transmission then stops
with four valid characters in the receiver. When MR2(4) is set to one,
CTSN must be at zero for the transmitter to operate. If MR2(4) is set
to zero, the MP pin will have no effect on the operation of the
transmitter.
MR1(7) is the bit that allows the receiver to control MP0. When MP0
is controlled by the receiver, the meaning of that pin will be RTS.
However, a point of confusion arises in that MP0 may also be
controlled by the transmitter. When the transmitter is controlling this
pin, its meaning is not RTS at all. It is, rather, that the transmitter has
finished sending its last data byte. Programming the MP0 pin to be
相关PDF资料 |
PDF描述 |
|---|---|
| SCC2692AE1N40,602 | IC DUART 40-DIP |
| SC16C654BIEC,551 | IC UART QUAD W/FIFO 64-LFBGA |
| ATMEGA644PA-AUR | IC MCU AVR 64K FLASH 44TQFP |
| SC16C554BIB80,551 | IC UART QUAD SOT315-1 |
| XR16C854CQTR-F | IC UART FIFO 128B QUAD 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCC7600003 | 制造商:Denon Electronics 功能描述:GRILL ASS'YSCC76 |
| SCC76BK003 | 制造商:Denon 功能描述:GRILLE ASSY, DENON |
| SCC9521002-01B | 制造商:AIMTEC 制造商全称:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller |
| SCC9521002-02B | 制造商:AIMTEC 制造商全称:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller |
| SCCA-1-01 | 制造商:Richco 功能描述:STANDOFF CABLE CLIP NAT 4MM SPC |
发布紧急采购，3分钟左右您将得到回复。