- 您现在的位置：买卖IC网 > PDF目录2016 > SI3011-F-FS (Silicon Laboratories Inc)IC VOICE DAA GCI/PCM/SPI 16SOIC PDF资料下载
参数资料
| 型号： | SI3011-F-FS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 58/128页 |
| 文件大小： | 0K |
| 描述： | IC VOICE DAA GCI/PCM/SPI 16SOIC |
| 标准包装： | 48 |
| 系列： | ISOcap™ |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
Si3050 + Si3011/18/19
Rev. 1.5
35
with the on-hook transition during pulse dialing. These
tests provide an inductive dc feed resulting in a large
voltage spike. This spike is caused by the line
inductance and the sudden decrease in current through
the loop when going on-hook. The traditional way of
dealing with this problem is to put a parallel RC shunt
across the hookswitch relay. The capacitor is large
(~1 F, 250 V) and relatively expensive. In the Si3050,
loop current can be controlled to achieve three distinct
on-hook speeds to pass spark quenching tests without
additional BOM components. Through the settings of
four bits in three registers, OHS (Register 16), OHS2
(Register 31), SQ0, and SQ1 (Register 59), a slow ramp
down of loop current can be achieved which induces a
delay between the time the OH bit is cleared and the
time the DAA actually goes on-hook.
To ensure proper operation of the DAA during pulse
dialing, disable the automatic resistor calibration that is
performed each time the DAA enters the off-hook state
by setting the RCALD bit (Register 25, bit 5).
5.22. Receive Overload Detection
The Voice DAA chipset is capable of monitoring and
reporting receive overload conditions on the line. Billing
tones, parallel phone off-hook events, polarity reversals
and other disturbances on the line may trigger multiple
levels of overload detection as described below.
Transient events less than 1.1 VPK on the line are
filtered out by the low-pass digital filter on the Si3050 +
Si3011 and Si3050+Si3019. The ROV and ROVI bits
are set when the received signal is greater than 1.1
VPK.
Both bits will continue to indicate an overload
condition until a zero is written to clear. The OVL mirrors
the function of the ROV and ROVI bits but it
automatically clears after the overload condition has
been removed. When the OVL bit returns to 0, the DAA
initiates
an
auto-calibration
sequence
that
must
complete before data can be transmitted. An external
interrupt can optionally be triggered by the ROVI bit by
setting the ROVM and INTE bits.
Certain events such as billing tones can be sufficiently
large to disrupt the line-derived power supply of the
Voice DAA line side device (Si3011, Si3018 or Si3019.)
To ensure that the device maintains the off-hook line
state during these events, the BTE bit should be set. If
such an event occurs while the BTE bit is set, the BTD
and BTDI bits will be asserted. A zero must be written to
the BTE bit to clear the BTD and BTDI bits. An external
interrupt can optionally be triggered by the BTDI bit by
setting the BTDM and INTE bits.
In the event that a line disturbance causes the loop
current to collapse below the minimum required
operating current of the Voice DAA, the DOD and DODI
bits will be set. An external interrupt can optionally be
triggered by the DODI bit by setting the DODM and
INTE bits.
5.23. Billing Tone Filter (Optional)
Optionally, a billing tone filter may be inserted between
the line and the voice DAA to minimize disruptions
caused by large billing tones. The notch filter design
requires two notches, one at 12 kHz and one at 16 kHz.
Because these components are expensive and few
countries utilize billing tones, this filter is typically placed
in an external dongle or added as a population option.
gives the component values.
L1 must carry the entire loop current. The series
resistance of the inductors is important to achieve a
narrow and deep notch. This design has more than
25 dB of attenuation at both 12 kHz and 16 kHz.
Figure 25. Billing Tone Filter
The billing tone filter affects the DAA’s ac termination
and return loss. The global compromise complex ac
termination as selected by ACIM[3:0] = 1111 passes
global return loss specifications with and without the
billing tone filter by at least 3 dB. This ac termination is
optimized
for
frequency
response
and
hybrid
Table 19. Component Values—Optional Billing
Tone Filters
Component
Value
C1,C2
0.027 F, 50 V, ±10%
C3
0.01 F, 250 V, ±10%
L1
3.3 mH, >120 mA, <10
, ±10%
L2
10 mH, >40 mA, <10
, ±10%
L2
C3
RIN G
TIP
From Line
To
DAA
C1
C2
L1
相关PDF资料 |
PDF描述 |
|---|---|
| SI3012-KS | IC LINE-SIDE DAA 16SOIC |
| SI3019-F-FS | IC LINE-SIDE DAA 16SOIC |
| SI3019-F-GM | IC VOICE GLOBAL DAA PROGR 20QFN |
| SI3063-F-FS | IC DAA ENH GLOB LINE-SIDE 16SOIC |
| SI3066-B-FS | IC DAA ENH FCC LINE-SIDE 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3011-F-FSR | 功能描述:电信线路管理 IC Si3050 FCC/TBR21 Voice DAA Line-Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| Si3011-F-FT | 功能描述:电信语音调制 IC Si3050 FCC/TBR21 Voice DAA Line-Side RoHS:否 制造商:Epson Electronics America 产品: 应用:Voice Guidance product 封装 / 箱体:PQFP-52 电源电压-最大:3.6 V, 5.5 V 最大工作温度: 最小工作温度: 封装: |
| SI3011-F-FTR | 制造商:Silicon Laboratories Inc 功能描述:SI3050 FCC/TBR21 VOICE DAA LINE-SIDE - LEAD-FREE - Tape and Reel |
| SI3011-F-GM | 制造商:SILABS 制造商全称:SILABS 功能描述:PROGRAMMABLE VOICE DAA SOLUTIONS |
| SI3011-F-GS | 制造商:SILABS 制造商全称:SILABS 功能描述:PROGRAMMABLE VOICE DAA SOLUTIONS |
发布紧急采购，3分钟左右您将得到回复。