- 您现在的位置：买卖IC网 > PDF目录2016 > SI3011-F-FS (Silicon Laboratories Inc)IC VOICE DAA GCI/PCM/SPI 16SOIC PDF资料下载
参数资料
| 型号： | SI3011-F-FS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 60/128页 |
| 文件大小： | 0K |
| 描述： | IC VOICE DAA GCI/PCM/SPI 16SOIC |
| 标准包装： | 48 |
| 系列： | ISOcap™ |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页当前第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
Si3050 + Si3011/18/19
Rev. 1.5
37
f. Set the OH bit to return to an off-hook state.
Immediately after returning to an off-hook state,
the off-hook counter must be allowed to expire.
This allows the line voltage to settle before
transmitting or receiving data. After 8 ms normal
data transmission and reception can begin. If a
non-compliant parallel device is present, then a
reply tone is not sent by the host tone generator
and the CO does not send the CID data. If all
devices on the line are Type II CID compliant,
then the host must mute its upstream data output
to avoid the propagation of its reply tone and the
subsequent CID data. When muting its upstream
data output, the host processor should return an
acknowledgement (ACK) tone to the CO
requesting transmission of CID data.
3. The CO then responds with CID data after receiving
the CID data, the host processor unmutes the
upstream data output and continues with normal
operation.
4. The muting of the upstream data path by the host
processor mutes the handset in a telephone
application so the user cannot hear the
acknowledgement tone and CID data being sent.
5. The CALD and the RCALD bits can be cleared to
re-enable the automatic calibrations when going
off-hook. The FOH[1:0] bits also can be programmed
to 01 to restore the default off-hook counter time.
Because of the nature of the low-power ADC, the data
presented on DTX can have up to a 10% dc offset. The
caller ID decoder must either use a high-pass or a
band-pass filter to accurately retrieve the caller ID data.
Figure 26. Implementing Type II Caller ID on the Si3050+Si3011/19
5.26. Overload Detection
The Si3050 can be programmed to detect an overload
condition that exceeds the normal operating power
range of the DAA circuit. To use the overload detection
feature, the following steps should be followed:
1. Set the OH bit (Register 5, bit 0) to go off-hook, and
wait 25 ms to allow line transients to settle.
2. Enable overload detection by then setting the OPE
bit (Register 17, bit 3).
If the DAA senses an overload situation it automatically
presents an 800
impedance to the line to reduce the
hookswitch current. At this time, the DAA also sets the
OPD bit (Register 19, bit 0) to indicate that an overload
condition exists. The line current detector within the
DAA has a threshold that is dependent on the ILIM bit
(Register 26). When ILIM = 0, the overload detection
threshold equals 160 mA. When ILIM = 1, the overload
detection threshold equals 60 mA. The OPE bit should
always be cleared before going off-hook.
Notes:
1. The off-hook counter and calibrations prevent transmission or reception of data for 402.75 ms (default) for the line
voltage to settle.
2.
The caller alert signal (CAS) tone transmits from the CO to signal an incoming call.
3.
The device is taken on-hook to read the line voltage in the LVS bits to detect parallel handsets. In this mode, no data is
transmitted on the DTX pin.
4.
When the device returns off-hook, the normal off-hook counter is reduced to 8 ms. If the CALD and RCALD bits are set,
then the automatic calibrations are not performed.
5.
After allowing the off-hook counter to expire (8 ms), normal transmission and reception can continue. If CID data
reception is required, send the appropriate signal to the CO at this time.
LINE
FOH[1] Bit
RCALD
Bit
CALD Bit
1
23
4
5
OH Bit
FOH[0] Bit
On-Hook
Off-H ook C ounter
and C alibration
(402.75 ms nominally)
Of f -Hook
CA S Tone
Rec eiv ed
On-Hook
Off-Hook Counter
(8 ms)
Of f -Hook
A ck
相关PDF资料 |
PDF描述 |
|---|---|
| SI3012-KS | IC LINE-SIDE DAA 16SOIC |
| SI3019-F-FS | IC LINE-SIDE DAA 16SOIC |
| SI3019-F-GM | IC VOICE GLOBAL DAA PROGR 20QFN |
| SI3063-F-FS | IC DAA ENH GLOB LINE-SIDE 16SOIC |
| SI3066-B-FS | IC DAA ENH FCC LINE-SIDE 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3011-F-FSR | 功能描述:电信线路管理 IC Si3050 FCC/TBR21 Voice DAA Line-Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| Si3011-F-FT | 功能描述:电信语音调制 IC Si3050 FCC/TBR21 Voice DAA Line-Side RoHS:否 制造商:Epson Electronics America 产品: 应用:Voice Guidance product 封装 / 箱体:PQFP-52 电源电压-最大:3.6 V, 5.5 V 最大工作温度: 最小工作温度: 封装: |
| SI3011-F-FTR | 制造商:Silicon Laboratories Inc 功能描述:SI3050 FCC/TBR21 VOICE DAA LINE-SIDE - LEAD-FREE - Tape and Reel |
| SI3011-F-GM | 制造商:SILABS 制造商全称:SILABS 功能描述:PROGRAMMABLE VOICE DAA SOLUTIONS |
| SI3011-F-GS | 制造商:SILABS 制造商全称:SILABS 功能描述:PROGRAMMABLE VOICE DAA SOLUTIONS |
发布紧急采购，3分钟左右您将得到回复。