- 您现在的位置：买卖IC网 > Datasheet目录517 > SM1212E433 (Semtech)RF EVAL FOR SX1212 433MHZ ISM Datasheet资料下载
参数资料
| 型号： | SM1212E433 |
| 厂商： | Semtech |
| 文件页数： | 19/77页 |
| 文件大小： | 0K |
| 描述： | RF EVAL FOR SX1212 433MHZ ISM |
| 标准包装： | 1 |
| 类型： | 收发器，ISM |
| 频率： | 433MHz |
| 适用于相关产品： | SX1212E |
| 已供物品： | 模块，天线，电源，软件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页
SX1212
ADVANCED COMMUNICATIONS & SENSING
In OOK mode, the phase difference between the I and Q channels is kept constant (independent of the transmitted
data). Thus, the first stage of up-conversion creates a fixed frequency signal at the low IF = Fdev (This explains
why the transmitted OOK spectrum is offset by Fdev).
OOK Modulation is accomplished by switching on and off the PA and PA regulator stages. By convention:
DATA = ' ' 1 ' ' ? PAon
DATA = ' ' 0 ' ' ? PAoff
After the interpolation filters, a set of four mixers combines the I and Q signals and converts them into a pair of
complex signals at the second intermediate frequency, equal to 1/8 of the LO frequency, or 1/9 of the RF
frequency. These two new I and Q signals are then combined and up-converted to the final RF frequency by two
quadrature mixers fed by the LO signal. The signal is pre-amplified, and then the transmitter output is driven by a
final power amplifier stage.
3.3.2. Bit Rate Setting
In Continuous transmit mode, setting the Bit Rate is useful to determine the frequency of DCLK. As explained in
section 5.3.2, DCLK will trigger an interrupt on the uC each time a new bit has to be transmitted.
BR =
F XTAL
2 * [ 1 + val ( MCParam _ BR _ C ) ] * [ 1 + val ( MCParam _ BR _ D ) ]
3.3.3. Alternative Settings
Bit rate, frequency deviation and TX interpolation filter settings are a function of the reference oscillator crystal
frequency, F XTAL . Settings other than those programmable with a 12.8 MHz crystal can be obtained by selection of
the correct reference oscillator frequency. Please contact your local Semtech representative for further details.
3.3.4. Fdev Setting in FSK Mode
The frequency deviation, Fdev, of the FSK transmitter is programmed through bits MCParam_Freq_dev:
Fdev =
F XTAL
32 * [ 1 + val ( MCParam _ Freq _ dev ) ]
For correct operation the modulation index ? should be such that:
β = 2 *
Fdev
BR
≥ 2
It should be noted that for communications between a pair of SX1212s, that Fdev should be at least 33 kHz to
ensure a correct operation on the receiver side.
3.3.5. Fdev Setting in OOK Mode
Fdev has no physical meaning in OOK transmit mode. However, as has been shown - due to the DDS baseband
signal generation, the OOK signal is always offset by “-Fdev” (see formulas is section 3.2.8). It is suggested that
Fdev retains its default value of 100 kHz in OOK mode.
Rev 2 – June 18th, 2009
Page 19 of 77
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SM1230E868 | BOARD EVAL XMITTER FOR SX1230 |
| SM16S-CM012-012 | SYNJET ZFLOW 50 PWM 12V |
| SM200P81 | RF MODULE 250/500MBPS 2.4GHZ SMA |
| SM2440G | LAMP T2 TELEPHONE SLIDE 24V .04A |
| SM3020G | LAMP T2 TELEPHONE SLIDE 30V .02A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SM-1220M | 制造商: 功能描述: 制造商:undefined 功能描述: |
| SM12-3/16-BLK-200FT | 制造商:SUMITOMO 功能描述:177-10101 SM12 3/16 BLK SPL |
| SM12-3/4-WHT-200FT | 制造商:SUMITOMO 功能描述:SM12-3/4-WHT-200FT 制造商:SUMITOMO 功能描述:177-10189 SM12 3/4 WHT SPL |
| SM12-3/8-BLK-200FT | 制造商:Sumitomo Wiring Systems LTD 功能描述:177-10107 SM12 3/8 BLK SPL |
| SM1230E868 | 功能描述:BOARD EVAL XMITTER FOR SX1230 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
发布紧急采购，3分钟左右您将得到回复。