参数资料
型号: ST10F168-Q3
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP144
封装: 28 X 28 MM, PLASTIC, QFP-144
文件页数: 30/74页
文件大小: 479K
代理商: ST10F168-Q3
ST10F168
36/74
15 - CAN MODULE
The integrated CAN module completely handles
the autonomous transmission and the reception of
CAN frames according to the CAN specification
V2.0 part B (active). The on-chip CAN module can
receive and transmit standard frames with 11-bit
identifiers as well as extended frames with 29-bit
identifiers.
The CAN Module Provides full CAN functionality
on up to 15 message objects. Message object 15
can be configured for basic CAN functionality.
Both modes provide separate masks for accep-
tance filtering, allowing a number of identifiers in
full CAN mode to be accepted and disregarding a
number of identifiers in basic CAN mode. All mes-
sage objects can be updated independently from
other objects and are equipped for the maximum
message length of 8 Bytes.
The bit timing is derived from the XCLK and is pro-
grammable up to a data rate of 1M Baud. The
CAN module uses two pins to interface to a bus
transceiver.
16 - WATCHDOG TIMER
The Watchdog Timer is a fail-safe mechanism
which prevents the microcontroller from malfunc-
tioning for long periods of time.
The Watchdog Timer is always enabled after a
reset of the chip and can only be disabled in the
time interval until the EINIT (end of initialization)
instruction has been executed.
Therefore, the chip start-up procedure is always
monitored. The software must be designed to ser-
vice the watchdog timer before it overflows. If, due
to hardware or software related failures, the soft-
ware fails to do so, the watchdog timer overflows
and generates an internal hardware reset. It pulls
the RSTOUT pin low in order to allow external
hardware components to be reset.
The Watchdog Timer is 16-bit, clocked with the
system clock divided by 2 or 128. The high Byte of
the watchdog timer register can be set to a
pre-specified reload value (stored in WDTREL).
Each time it is serviced by the application soft-
ware, the high Byte of the watchdog timer is
reloaded.
For security, rewrite WDTCON each
time before the watchdog timer is serviced.
Table 20 shows the watchdog time range for
25MHz CPU clock.
Table 20 : Watchdog time range (25MHz clock)
Reload value
in WDTREL
Prescaler for fCPU
2 (WDTIN = ‘0’)
128 (WDTIN = ‘1’)
FFh
20.48
s
1.31ms
00h
5.24ms
336ms
相关PDF资料
PDF描述
ST10F252M-4T3 16-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100
ST10F269DIETR 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, UUC
ST10F269Z2Q3 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144
ST10F269Z2Q6 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144
ST10F276Z5Q3 16-BIT, MROM, 64 MHz, RISC MICROCONTROLLER, PQFP144
相关代理商/技术参数
参数描述
ST10F168-Q6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16-BIT MCU WITH 256K BYTE FLASH MEMORY AND 8K BYTE RAM
ST10F168SQ3 功能描述:16位微控制器 - MCU 256K Flash 8K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
ST10F168SQ6 功能描述:16位微控制器 - MCU 256K Flash 8K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
ST10F252M 制造商:STMicroelectronics 功能描述:16-BIT MCU WITH 256 KBYTE FLASH MEMORY AND 16 KBYTE RAM - Rail/Tube
ST10F267-DT 制造商:STMicroelectronics 功能描述: