- 您现在的位置：买卖IC网 > PDF目录98143 > ST10R272LT6 (STMICROELECTRONICS) 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | ST10R272LT6 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, TQFP-100 |
| 文件页数： | 44/77页 |
| 文件大小： | 707K |
| 代理商： | ST10R272LT6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页
49/77
ST10R272L - ELECTRICAL CHARACTERISTICS
Note
The address float timings in Multiplexed bus mode (t11 and t45) use
instead of
.
Note that if the bit OWDDIS in SYSCON register is cleared, the PLL runs on its free-running
frequency and delivers the clock signal for the Oscillator Watchdog. If bit OWDDIS is set, then
the PLL is switched off.
Oscillator Watchdog (OWD)
When the clock option selected is direct drive or direct drive with prescaler, in order to provide
a fail safe mechanism in case of a loss of the external clock, an oscillator watchdog is
implemented as an additional functionality of the PLL circuitry. This oscillator watchdog
operates as follows:
After a reset, the Oscillator Watchdog is enabled by default. To disable the OWD, set bit 4 of
SYSCON register OWDDIS.
When the OWD is enabled, the PLL runs on its free-running frequency and increments the
Oscillator Watchdog counter. On each transition of the XTAL1 pin, the Oscillator Watchdog is
cleared. If an external clock failure occurs, then the Oscillator Watchdog counter overflows
(after 16 PLL clock cycles). The CPU clock signal will be switched to the PLL free-running
clock signal, and the Oscillator Watchdog Interrupt Request (XP3INT) is flagged. The CPU
clock will not switch back to the external clock even if a valid external clock exits on XTAL1 pin.
Only a hardware reset can switch the CPU clock source back to direct clock input.
When the OWD is disabled, the CPU clock is always fed from the oscillator input and the PLL
is switched off to decrease power supply current.
Phase locked loop
For all other combinations of pins P0.15-13 (P0H.7-5) during reset the on-chip phase locked
loop is enabled and provides the CPU clock. The PLL multiplies the input frequency by the
factor F which is selected via the combination of pins P0.15-13 (i.e. fCPU = fXTAL * F). With
every F’th transition of fXTAL the PLL circuit synchronizes the CPU clock to the input clock. In
this way, fCPU is constantly adjusted so it is locked to fXTAL. The slight variation causes a jitter
of fCPU which affects individual TCL duration.Therefore, AC characteristics that refer to TCLs
must be calculated using the minimum possible TCL.
The actual minimum value for TCL depends on the jitter of the PLL. As the PLL constantly
adjusts its output frequency, it corresponds to the applied input frequency (crystal or
oscillator). The relative deviation for periods of more than one TCL is lower than for one single
TCL. For a period of
N * TCL the minimum value is computed using the corresponding
deviation DN:
TCL
max
1 f
XTAL
DC
max
×
=
TCL
min
TCL
min
TCL
NOM
1
D
N
100
–
()
×
=
D
N
4
N 15
–
() %
[]
±
=
1
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C452PSIJ68 | 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68 |
| ST16C452ATIJ68 | 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68 |
| ST16C654IQ64/TR | 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQFP64 |
| ST18931CR | 16-BIT, 50 MHz, OTHER DSP, CPGA121 |
| ST40RA150XH6 | 32-BIT, 150 MHz, RISC PROCESSOR, PBGA372 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST10-S | 功能描述:电机驱动器 RoHS:否 制造商:Applied Motion 电机驱动类型:2035 Step 电源电压:12 V to 35 V 功率额定值:70 W 每转步距分辨率:200 to 400 框架大小 (NEMA): |
| ST10-S (5000-127) | 功能描述:电机驱动器 RoHS:否 制造商:Applied Motion 电机驱动类型:2035 Step 电源电压:12 V to 35 V 功率额定值:70 W 每转步距分辨率:200 to 400 框架大小 (NEMA): |
| ST10S008V4AR1800 | 功能描述:记忆卡连接器 Micro SD Conn P/P 1.25x13.2x14.85mm RoHS:否 制造商:Yamaichi Electronics 产品:Card Connectors 卡类型:microSD 类型: 节距: 方向: 安装风格:SMD/SMT 端接类型: 排数: 触点数量: 电流额定值:0.5 A 电压额定值:50 V |
| ST10S008V4B | 制造商:JAE 制造商全称:JAE 功能描述:microSDTM Small Memory Card Connector |
| ST10S008V4BR1800 | 功能描述:记忆卡连接器 microSD PUSH-PUSH LOW PROFILE 1.25MM H RoHS:否 制造商:Yamaichi Electronics 产品:Card Connectors 卡类型:microSD 类型: 节距: 方向: 安装风格:SMD/SMT 端接类型: 排数: 触点数量: 电流额定值:0.5 A 电压额定值:50 V |
发布紧急采购，3分钟左右您将得到回复。