参数资料
型号: ST52T430K3B6
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDIP32
封装: PLASTIC, SDIP-32
文件页数: 83/85页
文件大小: 1192K
代理商: ST52T430K3B6
ST52T430/E430
13 IMPORTANT NOTES
13.1 SILICON IDENTIFICATION
This document describes the limitations that apply
to ST52X430 devices.
13.2 SILICON LIMITATIONS
13.2.1 Exit from HALT with a long duration Ex-
ternal Interrupt signal.
Description.
Interrupt signals applied to the INT pin can cause
side effects after a wake-up from HALT mode if
these signals have a long duration. After the
interrupt signal, the device wakes-up and serves
the External Interrupt service routine; if the HALT
instruction is executed again when the signal
applied on the INT pin is still active, the device
immediately exits from HALT mode and the lower
priority interrupt routine is serviced.
Workaround.
To wake-up the device from the HALT mode, use
Exernal Interrupt signals whose time duration is
shorter than the shortest time between two
consecutive HALT instructions.
13.2.2 Interrupt priority change after a RINT in-
struction.
Description.
If an interrupt is reset with the RINT instruction
within its own interrupt routine, the priority level of
the interrupt becomes the lowest and the routine
can be immediately interrupted by a lower priority
interrupt request.
Workaround.
Avoid insertion of RINT instruction in its own
interrupt
routine,
unless interrupt is already
configured with lowest priority.
13.2.3 Zero Flag after Multiplication.
Description. If the LSB of the multiplication result
is 0, the Zero flag is set although the result is not 0.
Workaround.
To check if the result of the multiplication is 0,
control the Zero flag and the MSB.
13.3 HARDWARE TOOL WARNING
DESCRIPTION
13.3.1 ST52x430 low cost Evaluation Kits resis-
tors.
Description.
ST52x430LC/KIT
Evaluation
Kit
can
have
communication problems with some parallel ports
of the PC. In these cases, even if the port is well
configured as BI-DIRECTIONAL or EPP, the
following condition may occur:
- During write operations: a "write memory error"
appears on the output programmer window, and
the micro cannot be programmed.
- During read operations: the memory-dumped
code is always FFh even if the micro is not blank.
The problem is related to the signal levels driven
from some parallel ports of the PC and can be
solved by changing three SIL Resistors (4 single
resistors) on the programmer: R1, R2 and R4
placed close to the parallel port connector (see
figure below).
Workaround.
The suggestion is to substitute the original 680ohm
value (code xx681x) with 100ohm (code xx101x),
or 82ohm (code xx820x).
相关PDF资料
PDF描述
ST52T430K3T6 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQFP32
ST5X86V12HS 64-BIT, 120 MHz, MICROPROCESSOR, CPGA168
ST6235Q6 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST6240BQ6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
ST6242BQ1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
ST52T430K3M6 制造商:STMicroelectronics 功能描述:
ST52T430K3T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Three Timer/PWMs, ADC, SCI
ST52T440 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Timer/PWM, Analog Comparator, Triac/PWM Timer, WDG
ST52T440F0B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Timer/PWM, Analog Comparator, Triac/PWM Timer, WDG
ST52T440F0M6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Timer/PWM, Analog Comparator, Triac/PWM Timer, WDG