参数资料
型号: ST72651AR6T1E/XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, MICROCONTROLLER, PQFP64
封装: 10 X 10 MM, ROHS COMPLIANT, TQFP-64
文件页数: 141/161页
文件大小: 2656K
代理商: ST72651AR6T1E/XXX
ST72651AR6
80/161
Doc ID 7215 Rev 4
16-BIT TIMER (Cont’d)
11.4.3.2 Output Compare
In this section, the index, i, may be 1 or 2 because
there are 2 output compare functions in the 16-bit
timer.
This function can be used to control an output
waveform or indicate when a period of time has
elapsed.
When a match is found between the Output Com-
pare register and the free running counter, the out-
put compare function:
– Assigns pins with a programmable value if the
OCIE bit is set
– Sets a flag in the status register
– Generates an interrupt if enabled
Two 16-bit registers Output Compare Register 1
(OC1R) and Output Compare Register 2 (OC2R)
contain the value to be compared to the counter
register each timer clock cycle.
These registers are readable and writable and are
not affected by the timer hardware. A reset event
changes the OCiR value to 8000h.
Timing resolution is one count of the free running
counter: (
fCPU/CC[1:0]).
Procedure:
To use the output compare function, select the fol-
lowing in the CR2 register:
– Set the OCiE bit if an output is needed then the
OCMPi pin is dedicated to the output compare i
signal.
– Select the timer clock (CC[1:0]) (see Table 27
And select the following in the CR1 register:
– Select the OLVLi bit to applied to the OCMPi pins
after the match occurs.
– Set the OCIE bit to generate an interrupt if it is
needed.
When a match is found between OCRi register
and CR register:
– OCFi bit is set.
– The OCMPi pin takes OLVLi bit value (OCMPi
pin latch is forced low during reset).
– A timer interrupt is generated if the OCIE bit is
set in the CR2 register and the I bits are cleared
in the CC register (CC).
The OCiR register value required for a specific tim-
ing application can be calculated using the follow-
ing formula:
Where:
Δt
= Output compare period (in seconds)
fCPU
= CPU clock frequency (in hertz)
PRESC = Timer prescaler factor (2, 4 or 8 de-
pending on CC[1:0] bits, see Table 27
If the timer clock is an external clock, the formula
is:
Where:
Δt
= Output compare period (in seconds)
fEXT
= External timer clock frequency (in hertz)
Clearing the output compare interrupt request (i.e.
clearing the OCFi bit) is done by:
1. Reading the SR register while the OCFi bit is
set.
2. An access (read or write) to the OCiLR register.
The following procedure is recommended to pre-
vent the OCFi bit from being set between the time
it is read and the write to the OCiR register:
– Write to the OCiHR register (further compares
are inhibited).
– Read the SR register (first step of the clearance
of the OCFi bit, which may be already set).
– Write to the OCiLR register (enables the output
compare function and clears the OCFi bit).
MS Byte
LS Byte
OCiROCiHR
OCiLR
Δ OCiR = Δt * fCPU
PRESC
Δ OCiR = Δt
* fEXT
1
相关PDF资料
PDF描述
ST72652C4T1/XXX 8-BIT, MROM, MICROCONTROLLER, PQFP48
ST7267R8T1L/XXX 16-BIT, MROM, 30 MHz, RISC MICROCONTROLLER, PQFP64
ST7267C8T1/XXX 16-BIT, MROM, 30 MHz, RISC MICROCONTROLLER, PQFP48
ST72774S9T1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
ST72E734J6D0 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CDIP42
相关代理商/技术参数
参数描述
ST7265X-EVAL/MS 制造商:STMicroelectronics 功能描述:ST6 EVAL BD - Bulk
ST7265X-EVAL/PFD 制造商:STMicroelectronics 功能描述:USB FLASH EVAL - Bulk
ST7266 制造商:6940 功能描述:ST7266
ST7267C8T1L 制造商:STMicroelectronics 功能描述:
ST72681/R12 制造商:STMicroelectronics 功能描述:CONTROLLER FOR HIGH-PERFORMANCE BUS-POWERED USB 2.0 FLASH DR - Trays