收藏本站
参数资料
型号： TMP86CH47SUG
厂商： Toshiba Corporation
英文描述： Zener Diode; Application: General; Pd (mW): 500; Vz (V): 18.1 to 19.0; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
中文描述： 8位微控制器
文件页数： 42/160页
文件大小： 1627K
代理商： TMP86CH47SUG
Page 34
3. Interrupt Control Circuit
3.2 Interrupt enable register (EIR)
TMP86CH47SUG
Since interrupt latches can be read, the status for interrupt requests can be monitored by software.
Note: In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear IMF to
"0" (Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF or IL
(Enable interrupt by EI instruction)
In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute normally on
interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulating EF or IL
should be executed before setting IMF="1".
3.2
Interrupt enable register (EIR)
The interrupt enable register (EIR) enables and disables the acceptance of interrupts, except for the non-maskable
interrupts (Software interrupt, undefined instruction interrupt, address trap interrupt and watchdog interrupt). Non-
maskable interrupt is accepted regardless of the contents of the EIR.
The EIR consists of an interrupt master enable flag (IMF) and the individual interrupt enable flags (EF). These
registers are located on address 003AH and 003BH in SFR area, and they can be read and written by an instructions
(Including read-modify-write instructions such as bit manipulation or operation instructions).
3.2.1
Interrupt master enable flag (IMF)
The interrupt enable register (IMF) enables and disables the acceptance of the whole maskable interrupt.
While IMF = “0”, all maskable interrupts are not accepted regardless of the status on each individual interrupt
enable flag (EF). By setting IMF to “1”, the interrupt becomes acceptable if the individuals are enabled. When
an interrupt is accepted, IMF is cleared to “0” after the latest status on IMF is stacked. Thus the maskable inter-
rupts which follow are disabled. By executing return interrupt instruction [RETI/RETN], the stacked data,
which was the status before interrupt acceptance, is loaded on IMF again.
The IMF is located on bit0 in EIRL (Address: 003AH in SFR), and can be read and written by an instruction.
The IMF is normally set and cleared by [EI] and [DI] instruction respectively. During reset, the IMF is initial-
ized to “0”.
3.2.2
Individual interrupt enable flags (EF15 to EF4)
Each of these flags enables and disables the acceptance of its maskable interrupt. Setting the corresponding
bit of an individual interrupt enable flag to “1” enables acceptance of its interrupt, and setting the bit to “0” dis-
ables acceptance. During reset, all the individual interrupt enable flags (EF15 to EF4) are initialized to “0” and
all maskable interrupts are not accepted until they are set to “1”.
Note:In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear
IMF to "0" (Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF
or IL (Enable interrupt by EI instruction)
In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute nor-
mally on interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulat-
ing EF or IL should be executed before setting IMF="1".
Example 1 :Clears interrupt latches
DI
; IMF
←
0
LDW
(ILL), 1110100000111111B
; IL12, IL10 to IL6
←
0
EI
; IMF
←
1
Example 2 :Reads interrupt latches
LD
WA, (ILL)
; W
←
ILH, A
←
ILL
Example 3 :Tests interrupt latches
TEST
(ILL). 7
; if IL7 = 1 then jump
JR
F, SSET
相关PDF资料
PDF描述
TMP86CH49FG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 18.8 to 19.7; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CH72FG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 19.5 to 20.4; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CK74AFG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 20.2 to 21.1; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CM23AUG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 20.9 to 21.9; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CM27FG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 21.6 to 22.6; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
相关代理商/技术参数
参数描述
TMP86CH47U 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:CMOS 8 BIT MICROCONTROLLER
TMP86CH47UG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 16KB ROM 5V 44PQFP - Rail/Tube
TMP86CH49FG 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller
TMP86CH72FG 制造商:Toshiba America Electronic Components 功能描述:TLCS870/C 16K ROM , VFT - Rail/Tube
TMP86CK74AF 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*