- 您现在的位置：买卖IC网 > PDF目录1970 > TMS320VC5409GGU100 (Texas Instruments)IC DIG SIG PROCESSOR 144-BGA PDF资料下载
参数资料
| 型号： | TMS320VC5409GGU100 |
| 厂商： | Texas Instruments |
| 文件页数： | 8/93页 |
| 文件大小： | 0K |
| 描述： | IC DIG SIG PROCESSOR 144-BGA |
| 标准包装： | 160 |
| 系列： | TMS320C54x |
| 类型： | 定点 |
| 接口： | 主机接口，McBSP |
| 时钟速率： | 100MHz |
| 非易失内存： | ROM（32 kB） |
| 芯片上RAM： | 64kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.80V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LFBGA |
| 供应商设备封装： | 144-BGA MICROSTAR（12x12） |
| 包装： | 托盘 |
| 配用： | 296-15829-ND - DSP STARTER KIT FOR TMS320C5416 |
| 其它名称： | 296-10763 296-10763-5 296-10763-5-ND |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页
Introduction
16
April 1999 Revised October 2008
SPRS082F
Table 22. Terminal Functions (Continued)
TERMINAL
NAME
DESCRIPTION
I/O
INTERNAL
TERMINAL
NAME
DESCRIPTION
I/O
PIN STATE
INITIALIZATION, INTERRUPT, AND RESET OPERATIONS
IACK
O/Z
Interrupt acknowledge signal. IACK indicates receipt of an interrupt and that the program counter
is fetching the interrupt vector location designated by A15A0. IACK also goes into the
high-impedance state when OFF is low.
INT0
INT1
INT2
INT3
Schmitt
trigger
I
External user interrupts. INT0INT3 are prioritized and are maskable by the interrupt mask register
and the interrupt mode bit. INT0 INT3 can be polled and reset by way of the interrupt flag register.
NMI
Schmitt
trigger
I
Nonmaskable interrupt. NMI is an external interrupt that cannot be masked by way of the INTM or
the IMR. When NMI is activated, the processor traps to the appropriate vector location.
RS
Schmitt
trigger
I
Reset. RS causes the DSP to terminate execution and causes a reinitialization of the CPU and
peripherals. When RS is brought to a high level, execution begins at location 0FF80h of program
memory. RS affects various registers and status bits.
MP/MC
I
Microprocessor/microcomputer mode select. If active low at reset, microcomputer mode is
selected, and the internal program ROM is mapped into the upper program memory space. If the
pin is driven high during reset, microprocessor mode is selected, and the on-chip ROM is removed
from program space. MP/MC is only sampled at reset, and the MP/MC bit of the PMST register can
override the mode that is selected at reset.
MULTIPROCESSING SIGNALS
BIO
Schmitt
trigger
I
Branch control. A branch can be conditionally executed when BIO is active. If low, the processor
executes the conditional instruction. For the XC instruction, the BIO condition is sampled during the
decode phase of the pipeline; all other instructions sample BIO during the read phase of the
pipeline.
XF
O/Z
External flag output (latched software-programmable signal). XF is set high by the SSBX XF
instruction, set low by the RSBX XF instruction or by loading ST1. XF is used for signaling other
processors in multiprocessor configurations or used as a general-purpose output pin. XF goes into
the high-impedance state when OFF is low, and is set high at reset.
MEMORY CONTROL SIGNALS
DS
PS
IS
O/Z
Data, program, and I/O space select signals. DS, PS, and IS are always high unless driven low for
accessing a particular external memory space. Active period corresponds to valid address
information. DS, PS, and IS are placed into the high-impedance state in the hold mode; the signals
also go into the high-impedance state when OFF is low.
MSTRB
O/Z
Memory strobe signal. MSTRB is always high unless low-level asserted to indicate an external bus
access to data or program memory. MSTRB is placed in the high-impedance state in the hold mode;
it also goes into the high-impedance state when OFF is low.
READY
I
Data ready. READY indicates that an external device is prepared for a bus transaction to be
completed. If the device is not ready (READY is low), the processor waits one cycle and checks
READY again. Note that the processor performs ready detection if at least two software wait states
are programmed. The READY signal is not sampled until the completion of the software wait states.
R/W
O/Z
Read/write signal. R/W indicates transfer direction during communication to an external device.
R/W is normally in the read mode (high), unless it is asserted low when the DSP performs a write
operation. R/W is placed in the high-impedance state in hold mode; it also goes into the
high-impedance state when OFF is low.
IOSTRB
O/Z
I/O strobe signal. IOSTRB is always high unless low-level asserted to indicate an external bus
access to an I/O device. IOSTRB is placed in the high-impedance state in the hold mode; it also
goes into the high-impedance state when OFF is low.
HOLD
I
Hold. HOLD is asserted to request control of the address, data, and control lines. When
acknowledged by the C54x, these lines go into the high-impedance state.
I = Input, O = Output, Z = High-impedance, S = Supply
Although this pin includes an internal pulldown resistor, a 470- external pulldown is required. If the TRST pin is connected to multiple DSPs,
a buffer is recommended to ensure the VIL and VIH specifications are met.
相关PDF资料 |
PDF描述 |
|---|---|
| TMS470R1A384PZQ | IC RISC MCU 384K FLASH 100-LQFP |
| TMX320DM365BZCE | IC DIGITAL MEDIA SOC 338NFBGA |
| TMX320F28069UPFPA | IC MCU 32BIT 128KB FLASH 80HTQFP |
| TPS2371PWRG4 | IC PWR INTRFCE SW FOR POE 8TSSOP |
| TS3A24157RSERG4 | IC SWITCH DUAL SPDT 10UQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TMS320VC5409GGU-80 | 功能描述:数字信号处理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| TMS320VC5409PGE100 | 功能描述:数字信号处理器和控制器 - DSP, DSC Fixed-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| TMS320VC5409PGE100 | 制造商:Texas Instruments 功能描述:Digital Signal Processor IC |
| TMS320VC5409PGE-80 | 功能描述:数字信号处理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| TMS320VC5409ZGU100 | 功能描述:数字信号处理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。