- 您现在的位置：买卖IC网 > Datasheet目录368 > W19B320BTT7H (Winbond Electronics)IC FLASH 32MBIT 70NS 48TSOP Datasheet资料下载
参数资料
| 型号： | W19B320BTT7H |
| 厂商： | Winbond Electronics |
| 文件页数： | 12/51页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 32MBIT 70NS 48TSOP |
| 标准包装： | 96 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 32M（4M x 8，2M x 16） |
| 速度： | 70ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 48-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 48-TSOP |
| 包装： | 托盘 |
| 其它名称： | W19B320BTT-H W19B320BTT-H-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
W19B320BT/B DATASHEET
Once the Embedded Program algorithm is complete, the bank then returns to the read mode and
addresses are no longer latched. The system can determine the status of the program operation by
using DQ7, DQ6, or RY/#BY. Please refer to the Write Operation Status section for bits' information.
Any commands written to the device during the Embedded Program Algorithm are ignored. Please note
that a hardware reset will immediately stop the program operation. The program command sequence
should be reinitiated when the bank has returned to the read mode, in order to ensure data integrity.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed
from “0” back to “1.” If trying to do so may cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6
status bits to indicate that the operation is successful. However, a succeeding read will show that the
data is still “0.” Only erase operations can change “0” to “1.”
6.2.5
Unlock Bypass Command Sequence
The unlock bypass feature provides the system to program bytes or words to a bank which is faster
than using the standard program command sequence. The unlock bypass command sequence is
initiated by first writing two unlock cycles. And a third write cycle containing the unlock bypass
command, 20h, is followed. Then, the bank enters into the unlock bypass mode. A two-cycle unlock
bypass program command sequence is all that required to program in this mode. The first cycle in this
sequence contains the unlock bypass program command, A0h; the second cycle contains the program
address and data. In the same manner, additional data is programmed. This mode dispenses with the
initial two unlock cycles which required in the standard program command sequence, resulting in faster
total programming time.
All through the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset
commands are valid. The system must issue the two-cycle unlock bypass reset command sequence to
exit the unlock bypass mode. The first cycle must contain the bank address and the data 90h. The
second cycle needs to contain the data 00h. Then, the bank returns to the read mode.
The device offers accelerated program operations by the #WP/ACC pin. When the V HH is set at the
#WP/ACC pin, the device automatically enters into the Unlock Bypass mode. Then, the two-cycle
Unlock Bypass program command sequence may be written. To accelerate the operation, the device
must use the higher voltage on the #WP/ACC pin. Please note that the #WP/ACC pin must not be at
V HH in any operation other than accelerated programming; otherwise the device may be damaged. In
addition, the #WP/ACC pin must not be left floating or unconnected; otherwise the device inconsistent
behavior may occur.
6.2.6
Chip Erase Command Sequence
Chip erase is a six-bus cycle operation. Writing two unlock cycles initiate the chip erase command
sequence, which is followed by a set-up command. After chip erase command, two additional unlock
write cycles are then followed, which in turn invokes the Embedded Erase algorithm. The system
preprogram is not required prior to erase. Before electrical erase, the Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data pattern. Any controls or
timings during these operations is not required in system.
As the Embedded Erase algorithm is complete, the bank returns to the read mode and addresses are
no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6,
DQ2, or RY/#BY. Please refer to the Write Operation Status section for information on these status bits.
Publication Release Date:Dec, 22, 2008
- 12 -
Revisionv A5
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q128BVEIG | IC SPI FLASH 128MBIT 8WSON |
| W25Q16BVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16CVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16DWSFIG | IC FLASH SPI 16MBIT 16SOIC |
| W25Q16VSFIG | IC FLASH 16MBIT 80MHZ 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W19L-E02050 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E03040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E04040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19U_5LGA WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| W1A | 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 类别:盒，外壳，支架 >> 箱 系列:工具 产品目录绘图:SR Series Standard 特色产品:Customize Your Enclosure 标准包装:1 系列:S 容器 - 类型:盒 尺寸/尺寸:3.600" L x 2.250" W（91.44mm x 57.15mm） 高度:1.500"（38.10mm） 面积 (L x W):8.10"（52.3cm） 设计:手持，分叉式双侧 材质:塑料 - ABS 颜色:杏黄 厚度:0.100"（2.54mm） 特点:PCB 支座 额定值:IP40，NEMA 1 材料可燃性额定值:UL94 HB 装运信息:从 Digi-Key 运送 重量:0.137 磅（62.14g） 相关产品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名称:111-I ALMOND111-IA111-IALMONDSR111-IA |
发布紧急采购，3分钟左右您将得到回复。