- 您现在的位置：买卖IC网 > Datasheet目录368 > W19B320BTT7H (Winbond Electronics)IC FLASH 32MBIT 70NS 48TSOP Datasheet资料下载
参数资料
| 型号： | W19B320BTT7H |
| 厂商： | Winbond Electronics |
| 文件页数： | 9/51页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 32MBIT 70NS 48TSOP |
| 标准包装： | 96 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 32M（4M x 8，2M x 16） |
| 速度： | 70ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 48-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 48-TSOP |
| 包装： | 托盘 |
| 其它名称： | W19B320BTT-H W19B320BTT-H-ND |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
W19B320BT/B DATASHEET
protected sectors can be programmed or erased by selecting the sector addresses. What if V ID is
removed from the #RESET pin, all the previously protected sectors are protected again.
6.1.12 Security Sector Flash Memory Region
The Security Sector feature provides an OTP memory region that enables permanent device
identification through an Electronic Serial Number (ESN). The Security Sector uses a Security Sector
Indicator Bit (DQ7) to indicate whether the Security Sector is locked or not when shipped from the
factory. The DQ7 is permanently set when it is in the factory and cannot be changed, which prevents
copying of a factory locked part. This ensures the security of the ESN when the product is shipped to
the field. This issue should be considered during system design. Winbond offers the device with the
Security Sector either factory locked or customer lockable. The factory-locked version is always
protected when shipped from the factory, and has the Security Sector Indicator Bit permanently set to
“1” The customer-lockable version is shipped with the Security Sector unprotected, which allowing
customers to utilize the sector in any ways they choose. The customer-lockable version has the
Security Sector Indicator Bit permanently set to “0.” Thus, the Security Sector Indicator Bit prevents
customer-lockable devices from being used to replace devices that are factory locked.
The system accesses the Security Sector through a command sequence (see “Enter Security
Sector/Exit Security Sector Command Sequence”). After the system has written the Enter Security
Sector command sequence, it may read the Security Sector by using the addresses normally occupied
by the boot sectors. This mode of operation continues until the system issues the Exit Security Sector
command sequence, or until power is removed from the device. On power-up, or following a hardware
reset, the device reverts to sending commands to the boot sectors.
Factory Locked: Security Sector Programmed and Protected At the Factory
The device Security Sector is protected when it is shipped from the factory, and it cannot be modified in
any way. The device is available to be preprogrammed by one of the following:
?
?
?
A random, secure ESN only
Customer code through the supplier's service
Both a random, secure ESN and customer code through supplier's service.
In devices with an ESN, the Bottom Boot device will be with the 16-byte ESN in the lowest addressable
memory area at addresses 000000h–000007h in word mode (or 000000h–00000Fh in byte mode). In
the Top Boot device the starting address of the ESN will be at the bottom of the highest 8 Kbytes boot
sector at addresses 1FF000h–1FF007h in word mode (or addresses 3FE000h–3FE00Fh in byte
mode). Customers may choose have their code programmed by Winbond. Winbond can program the
customer’s code, with or without the random ESN. The devices are then shipped with the Security
Sector permanently locked.
Customer Lockable: Security Sector NOT Programmed or Protected At the Factory
If the security feature is not necessary, the Security Sector can be seen as an additional OTP memory
space. When in system design, this issue should be considered. The Security Sector can be read,
programmed; but cannot be erased. Please note that when programming the Security Sector, the
accelerated programming (ACC) and unlock bypass functions are not available. The Security Sector
area can be protected using one of the following procedures:
?
Write the three-cycle Enter Security Sector Region command sequence, and then follow the in-
system sector protect algorithm, except that #RESET may be at either V IH or V ID . This allows
in-system protection of the Security Sector without raising any device pin to a high voltage.
Please note that this method is only suitable for the Security Sector.
Publication Release Date:Dec, 22, 2008
-9-
Revisionv A5
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q128BVEIG | IC SPI FLASH 128MBIT 8WSON |
| W25Q16BVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16CVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16DWSFIG | IC FLASH SPI 16MBIT 16SOIC |
| W25Q16VSFIG | IC FLASH 16MBIT 80MHZ 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W19L-E02050 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E03040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E04040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19U_5LGA WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| W1A | 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 类别:盒，外壳，支架 >> 箱 系列:工具 产品目录绘图:SR Series Standard 特色产品:Customize Your Enclosure 标准包装:1 系列:S 容器 - 类型:盒 尺寸/尺寸:3.600" L x 2.250" W（91.44mm x 57.15mm） 高度:1.500"（38.10mm） 面积 (L x W):8.10"（52.3cm） 设计:手持，分叉式双侧 材质:塑料 - ABS 颜色:杏黄 厚度:0.100"（2.54mm） 特点:PCB 支座 额定值:IP40，NEMA 1 材料可燃性额定值:UL94 HB 装运信息:从 Digi-Key 运送 重量:0.137 磅（62.14g） 相关产品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名称:111-I ALMOND111-IA111-IALMONDSR111-IA |
发布紧急采购，3分钟左右您将得到回复。