- 您现在的位置：买卖IC网 > Datasheet目录368 > W19B320BTT7H (Winbond Electronics)IC FLASH 32MBIT 70NS 48TSOP Datasheet资料下载
参数资料
| 型号： | W19B320BTT7H |
| 厂商： | Winbond Electronics |
| 文件页数： | 15/51页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 32MBIT 70NS 48TSOP |
| 标准包装： | 96 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 32M（4M x 8，2M x 16） |
| 速度： | 70ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 48-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 48-TSOP |
| 包装： | 托盘 |
| 其它名称： | W19B320BTT-H W19B320BTT-H-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
W19B320BT/B DATASHEET
toggle bit with the first one. If the toggle bit is not toggling, the device has completed the program or erasure
operation. The system can read array data on DQ0-DQ7 on the following read cycle.
However, if after the initial two read cycles, the system finds that the toggle bit is still toggling, the system
also should note whether the value of DQ5 is high or not(see the section on DQ5). If DQ5 is high, the system
should then determine again whether the toggle bit is toggling or not, since the toggle bit may have stopped
toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed
the program or erasure operation. If it is still toggling, the device did not complete the operation, and the
system must write the reset command to return to reading array data.
Then the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system
may continue to monitor the toggle bit and DQ5 through successive read cycles, and determines the status
as described in the previous paragraph. Alternatively, the system may choose to perform other system tasks.
In this case, the system must start at the beginning of the algorithm while it returns to determine the status of
the operation.
6.3.5
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit.
DQ5 produces “1” under these conditions which indicates that the program or erase cycle was not
successfully completed.
The device may output “1” on DQ5 if the system tries to program “1” to a location that was previously
programmed to “0.” Only the erase operation can change “0” back to “1.” Under this condition, the device
stops the operation, and while the timing limit has been exceeded, DQ5 produces “1.”
Under both these conditions, the system must write the reset command to return to the read mode.
6.3.6
DQ3: Sector Erase Timer
After writing a sector erasure command sequence, the system may read DQ3 to determine whether erasure
has begun or not. (The sector erase timer does not apply to the chip erase command.) The entire time-out
applies after each additional sector erasure command if additional sectors are selected for erasure. Once the
timeout period has completed, DQ3 switches from “0” to “1.” If the time between additional sector erase
commands from the system can be assumed to be less than 50 μ s, the system need not monitor, DQ3 does
not need to be monitored. Please also refer to Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of DQ7 ( #Data Polling ) or DQ6
(Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3
is“1,” the Embedded Erase algorithm has begun; all further commands are ignored until the erase operation
is complete. If DQ3 is “0,” the device will accept additional sector erase commands.
The system software should check the status of DQ3 before and following each subsequent sector erase
command to ensure the command has been accepted. If DQ3 is high on the second status check, the last
command might not have been accepted.
Publication Release Date:Dec, 22, 2008
- 15 -
Revisionv A5
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q128BVEIG | IC SPI FLASH 128MBIT 8WSON |
| W25Q16BVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16CVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16DWSFIG | IC FLASH SPI 16MBIT 16SOIC |
| W25Q16VSFIG | IC FLASH 16MBIT 80MHZ 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W19L-E02050 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E03040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E04040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19U_5LGA WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| W1A | 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 类别:盒，外壳，支架 >> 箱 系列:工具 产品目录绘图:SR Series Standard 特色产品:Customize Your Enclosure 标准包装:1 系列:S 容器 - 类型:盒 尺寸/尺寸:3.600" L x 2.250" W（91.44mm x 57.15mm） 高度:1.500"（38.10mm） 面积 (L x W):8.10"（52.3cm） 设计:手持，分叉式双侧 材质:塑料 - ABS 颜色:杏黄 厚度:0.100"（2.54mm） 特点:PCB 支座 额定值:IP40，NEMA 1 材料可燃性额定值:UL94 HB 装运信息:从 Digi-Key 运送 重量:0.137 磅（62.14g） 相关产品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名称:111-I ALMOND111-IA111-IALMONDSR111-IA |
发布紧急采购，3分钟左右您将得到回复。