- 您现在的位置：买卖IC网 > PDF目录276892 > W19B320SBB9B (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 PDF资料下载
参数资料
| 型号： | W19B320SBB9B |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封装： | TFBGA-48 |
| 文件页数： | 3/52页 |
| 文件大小： | 1869K |
| 代理商： | W19B320SBB9B |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
W19B(L)320ST/B
Publication Release Date: March 23, 2004
- 11 -
Revision A2
6.2.1 Reading Array Data
After device power-up, it is automatically set to reading array data. There is no commands are
required to retrieve data. After completing an Embedded Program or Embedded Erase algorithm, the
device is ready to read array data.
After the device accepts an Erase Suspend command, it enters the erase-suspend-read mode. After
this the system can read data from any non-erase-suspended sector. And then, after completing a
programming operation in the Erase Suspend mode, the system may once again read array data with
the same exception. Please refer to Erase Suspend/Erase Resume Commands section for detail
information.
The system must initiate the reset command to return the device to read (or erase-suspend-read)
mode if DQ5 goes high during an active program or erase operation; otherwise, the device is in the
autoselect mode. See Reset Command section and Requirements for Reading Array Data in the
Device Bus Operations section for more information.
6.2.2 Reset Command
The device will be to the read or erase-suspend-read mode when writing the reset command. For this
command, the address bits are Don’t Care.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to which the system was writing to the read mode. Once
erasure begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence
before programming begins. This resets the device, to which the system was writing to the read mode.
If the program command sequence is written to the device, in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode. When programming begins, the
device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command
sequence. When in the autoselect mode, the reset command must be written to return to the read
mode. If the device entered into the autoselect mode while in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the device
to the read mode (or erase-suspend-read mode if the device was in Erase Suspend).
6.2.3 Autoselect Command Sequence
The autoselect command sequence provides the host system to access the manufacturer and device
codes, and determine whether a sector is protected or not. This is an alternative method, which is
intended for PROM programmers and requires VID on address pin A9. The autoselect command
sequence may be written to an address within the device that is either in the read or erase-suspend-
read mode. When the device is actively programming or erasing, the autoselect command may not be
written.
The first writing two unlock cycles initiate the autoselect command sequence. This is followed by a
third write cycle that contains the autoselect command. The device then enters into the autoselect
mode. The system may read at any address without initiating another autoselect command sequence:
A read cycle at address XX00h returns the manufacturer code.
A read cycle at address XX01h in word mode(or XX02h in byte mode) returns the device code.
相关PDF资料 |
PDF描述 |
|---|---|
| W19L320STT9K | 2M X 16 FLASH 3.3V PROM, 90 ns, PDSO48 |
| W25X32-VSFI | 32M X 1 FLASH 2.7V PROM, PDSO16 |
| WS512K820MA | 512K X 8 MULTI DEVICE SRAM MODULE, 20 ns, CDIP32 |
| WS512K8L45IA | 512K X 8 MULTI DEVICE SRAM MODULE, 45 ns, CDIP32 |
| WF512K32F-150HM5 | 512K X 32 FLASH 5V PROM MODULE, 150 ns, HIP66 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W19L-E02050 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E03040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E04040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19U_5LGA WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| W1A | 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 类别:盒，外壳，支架 >> 箱 系列:工具 产品目录绘图:SR Series Standard 特色产品:Customize Your Enclosure 标准包装:1 系列:S 容器 - 类型:盒 尺寸/尺寸:3.600" L x 2.250" W（91.44mm x 57.15mm） 高度:1.500"（38.10mm） 面积 (L x W):8.10"（52.3cm） 设计:手持，分叉式双侧 材质:塑料 - ABS 颜色:杏黄 厚度:0.100"（2.54mm） 特点:PCB 支座 额定值:IP40，NEMA 1 材料可燃性额定值:UL94 HB 装运信息:从 Digi-Key 运送 重量:0.137 磅（62.14g） 相关产品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名称:111-I ALMOND111-IA111-IALMONDSR111-IA |
发布紧急采购，3分钟左右您将得到回复。