参数资料
| 型号： | W25Q16CVSSIG |
| 厂商： | Winbond Electronics |
| 文件页数： | 12/81页 |
| 文件大小： | 0K |
| 描述： | IC SPI FLASH 16MBIT 8SOIC |
| 标准包装： | 90 |
| 系列： | SpiFlash® |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 16M（2M x 8） |
| 速度： | 104MHz |
| 接口： | SPI 串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页
W25Q16CV
6.
6.1
FUNCTIONAL DESCRIPTION
SPI OPERATIONS
6.1.1
Standard SPI Instructions
The W25Q16CV is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge CLK.
SPI bus operation Mode 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and
Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is
not being transferred to the Serial Flash. For Mode 0, the CLK signal is normally low on the falling and
rising edges of /CS. For Mode 3, the CLK signal is normally high on the falling and rising edges of /CS.
6.1.2
Dual SPI Instructions
The W25Q16CV supports Dual SPI operation when using the “ Fast Read Dual Output (3Bh)” and “Fast
Read Dual I/O (BBh) ” instructions. These instructions allow data to be transferred to or from the device at
two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are ideal for
quickly downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical
code directly from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins become
bidirectional I/O pins: IO0 and IO1.
6.1.3
Quad SPI Instructions
The W25Q16CV supports Quad SPI operation whe n using the “ Fast Read Quad Output (6Bh) ”, “ Fast
Read Quad I/O (EBh) ”, “Word Read Quad I/O (E7h) ” and “Octal Word Read Quad I/O (E3h) ” instructions.
These instructions allow data to be transferred to or from the device four to six times the rate of ordinary
Serial Flash. The Quad Read instructions offer a significant improvement in continuous and random
access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP).
When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP
and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad
Enable bit (QE) in Status Register-2 to be set.
6.1.4
Hold Function
For Standard SPI and Dual SPI operations, the /HOLD signal allows the W25Q16CV operation to be
paused while it is actively selected (when /CS is low). The /HOLD function may be useful in cases where
the SPI data and clock signals are shared with other devices. For example, consider if the page buffer
was only partially written when a priority interrupt requires use of the SPI bus. In this case the /HOLD
function can save the state of the instruction and the data in the buffer so programming can resume
where it left off once the bus is available again. The /HOLD function is only available for standard SPI and
Dual SPI operation, not during Quad SPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
- 12 -
相关PDF资料 |
PDF描述 |
|---|---|
| AX1000-FG896I | IC FPGA AXCELERATOR 1M 896-FBGA |
| W25Q16BVZPIG | IC SPI FLASH 16MBIT 8WSON |
| W25Q80BVDAIG | SPI FLASH 8MBIT 8-DIP |
| EP1S10F780C6N | IC STRATIX FPGA 10K LE 780-FBGA |
| EPF10K30AFC484-1 | IC FLEX 10KA FPGA 30K 484-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25Q16CVSSIG TR | 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 16M-BIT, 4KB UNIFORM |
| W25Q16CVSSIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q16CVTCAG | 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q16CVTCAP | 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q16CVTCIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
发布紧急采购，3分钟左右您将得到回复。