- 您现在的位置：买卖IC网 > Datasheet目录368 > W29GL064CB7S (Winbond Electronics)IC FLASH 64MBIT 70NS 48TSOP Datasheet资料下载
参数资料
| 型号： | W29GL064CB7S |
| 厂商： | Winbond Electronics |
| 文件页数： | 15/68页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 64MBIT 70NS 48TSOP |
| 标准包装： | 96 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 64M（8M x 8，4M x 16） |
| 速度： | 70ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 48-TSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
W29GL064C
7.2.9
Erasing the Memory Array
Sector Erase and Chip Erase are the two possible types of operations executed on the memory array.
Sector Erase operation erases one or more selected sectors and this can be simultaneous. Chip
Erase operation erases the entire memory array, except for any protected sectors.
7.2.9.1
Sector Erase
The sector erase operation returns all selected sectors in memory to the “1” state, effectively clearing
all data. This action requires six instruction cycles to commence the erase operation. The unlock
sequence is the first two cycles, followed by the configuration cycle, the fourth and fifth are
also ”unlock cycles”, and the Sector Erase instruction is the sixth cycle. An internal 50μs time-out
counter is started once the sector erase instruction sequence has been completed. During this time,
additional sector addresses and Sector Erase commands may be issued, thus allowing for multiple
sectors to be selected and erased simultaneously. Once the 50μs time-out counter has reached its
limit, no additional command instructions will be accepted and the embedded sector erase algorithm
will commence.
Note, that the 50μs time-out counter restarts after every sector erase instruction sequence. The device
will abort and return to Read mode, if any instruction other than Sector Erase or Erase Suspend is
attempted during the time-out period.
Once the embedded sector erase algorithm begins, all instructions except Erase Suspend or
Hardware Reset will be ignored. The hardware reset will abort the erase operation and return the
device to the Read mode.
The embedded sector erase algorithm status can be verified by the following:
Status
Time-out period
In progress
Exceeded time limit
DQ7
0
0
0
DQ6
Toggling
Toggling
Toggling
DQ5
0
0
1
DQ3 1
0
1
1
DQ2
Toggling
Toggling
Toggling
RY/#BY 2
0
0
0
Table 7-4
Note :
Polling During Embedded Sector Erase Operation
1.
2.
3.
4.
The DQ3 status bit is the 50μs time-out indicator. When DQ3=0, the 50μs time-out counter has not yet reached zero
and the new Sector Erase instruction maybe issued to specify the address of another sector to be erased. When
DQ3=1, the 50μs time-out counter has expired and the Sector Erase operation has already begun. Erase Suspend is
the only valid instruction that maybe issued once the embedded erase operation is underway.
RY/#BY is an open drain output pin and should be connected to VCC through a high value pull-up resistor.
When an attempt is made to erase only protected sector(s), the erase operation will abort thus preventing any data
changes in the protected sector(s). DQ7 will output “0” and DQ6 will toggle briefly (100μs or less) before aborting and
returning the device to Read mode. If unprotected sectors are also specified, however, they will be erased normally
and the protected sector(s) will remain unchanged.
DQ2 is a localized indicator showing a specified sector is undergoing erase operation or not. DQ2 toggles when user
reads at the addresses where the sectors are actively being erased (in erase mode) or to be erased (in erase
suspend mode).
Publication Release Date: August 2, 2013
9
Revision H
相关PDF资料 |
PDF描述 |
|---|---|
| W29GL128CL9T | IC FLASH 128MBIT 90NS 56TSOP |
| W631GG6KB-15 | IC DDR3 SDRAM 1GBIT 96WBGA |
| W9412G6IH-5 | IC DDR-400 SDRAM 128MB 66TSSOPII |
| W9412G6JH-5I | IC DDR SDRAM 128MBIT 66TSOPII |
| W9425G6EH-5 | IC DDR-400 SDRAM 256MB 66TSSOPII |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W29GL064CH7B | 制造商:WINBOND 制造商全称:Winbond 功能描述:64M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE |
| W29GL064CH7T | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 64MBIT 70NS 56TSOP |
| W29GL064CL7B | 制造商:WINBOND 制造商全称:Winbond 功能描述:64M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE |
| W29GL064CL7T | 制造商:WINBOND 制造商全称:Winbond 功能描述:64M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE |
| W29GL064CT7A | 功能描述:IC FLASH 64MBIT 70NS 48TFBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:4G（256M x 16） 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP I 包装:Digi-Reel® 其它名称:557-1461-6 |
发布紧急采购，3分钟左右您将得到回复。