参数资料
| 型号： | W29GL128CL9B |
| 厂商： | Winbond Electronics |
| 文件页数： | 17/67页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 128MBIT 90NS 64LFBGA |
| 标准包装： | 171 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 128M（16M x 8，8M x 16） |
| 速度： | 90ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-LBGA |
| 供应商设备封装： | 64-LFBGA（11x13） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
W29GL128C
7.2.12 Program Suspend/Resume
Once a program operation is in progress, a Program Suspend is the only valid instruction that maybe
executed. Verifying if the device has entered the Program-Suspend Read mode after executing the
Program-Suspend instruction, can be done by checking the RY/#BY and DQ6. Programming should
halt within 15μs maximum (5μs typical).
Any sector(s) can be read except those being program suspended. Trying to read a sector being
program suspended is invalid. Before another program operation can be executed, a Resume
instruction must be performed and DQ6 toggling bit status has to be verified. Use the status register
bits shown in the following table to determine the current state of the device:
Status
DQ7 DQ6 DQ5 DQ3 DQ2 DQ1 RY/#BY
Program suspend read in program suspended sector
Program suspend read in non-program suspended sector
Invalid
Data Data Data Data Data Data
1
1
Table 7-7
Polling During Embedded Program Suspend
Instruction sets such as read silicon ID, sector protect verify, program, CFI query can also be executed
during Program/Erase-Suspend mode.
7.2.13 Program Resume
The program Resume instruction is valid only when the device is in Program-Suspended mode. Once
the program resumes, another Program Suspend instruction can be executed. Insure there is at least
a 5μs interval between Program Resume and the next Suspend instruction.
7.2.14 Write Buffer Programming Operation
Write Buffer Programming Operation, programs 64bytes or 32words in a two step programming
operation. To begin execution of the Write Buffer Programming, start with the first two unlock cycles,
the third cycle writes the programming Sector Address destination followed by the Write Buffer Load
Instruction (25h). The fourth cycle repeats the Sector Address, while the write data is the number of
intended word locations to be written minus one. (Example, if the number of word locations to be
written is 9, then the value would be 8h.) The 5 th cycle is the first starting address/data set. This will be
the first pair to be programmed and consequentially, sets the “write-buffer-page” address. Repeat
Cycle 5 format for each additional address/data sets to be written to the buffer. Keep in mind all sets
must remain within the write buffer page address range. If not, operation will ABORT.
The “write-buffer-page” is selected by choosing address A[22:5].
The second step will be to program the contents of the write buffer page. This is done with one cycle,
containing the sector address that was used in step one and the “Write to Buffer Program Confirm”
instruction (29h).
Standard suspend/resume commands can be used during the operation of the write-buffer. Also, once
the write buffer programming operation is finished, it’ll return to the normal READ mode.
Write buffer programming can be conducted in any sequence. However the CFI functions, autoselect,
Secured Silicon sector are not functional when program operation is in progress. Multiple write buffer
programming operations on the same write buffer address range without intervention erase is
accessible. Any bit in a write buffer address range cannot be programmed from 0 back to 1.
Publication Release Date: August 2, 2013
11
Revision H
相关PDF资料 |
PDF描述 |
|---|---|
| W631GG6KB-12 | IC DDR3 SDRAM 1GBIT 96WBGA |
| AMC20DRAS-S734 | CONN EDGECARD 40POS .100 R/A PCB |
| FMC12DREI-S13 | CONN EDGECARD 24POS .100 EXTEND |
| EPF6024AQC240-2N | IC FLEX 6000 FPGA 24K 240-PQFP |
| EPF6024AQC240-2 | IC FLEX 6000 FPGA 24K 240-PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W29GL128CL9B TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 64LFBGA |
| W29GL128CL9T | 功能描述:IC FLASH 128MBIT 90NS 56TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| W29GL128CL9T TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 56TSOP |
| W29NK50ZD | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:N-CHANNEL 500 V - 0.11? - 29A TO-247 Fast Diode SuperMESH? MOSFET |
| W2A-1819 | 制造商:Nexans 功能描述:MULTI CONDUCTORS |
发布紧急采购，3分钟左右您将得到回复。