- 您现在的位置：买卖IC网 > PDF目录205930 > X40411S8I-C 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | X40411S8I-C |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | PLASTIC, SOIC-8 |
| 文件页数： | 23/25页 |
| 文件大小： | 532K |
| 代理商： | X40411S8I-C |
X40410/X40411/X40414/X40415
Characteristics subject to change without notice.
7 of 25
REV 1.3.6 2/11/04
www.xicor.com
BP: Block Protect Bit (Nonvolatile)
The Block Protect Bit, BP, determines which blocks of
the array are write protected. A write to a protected
block of memory is ignored. The block protect bits will
prevent write operations to half or none of the array.
PUP1, PUP0: Power Up Bits (Nonvolatile)
The Power Up bits, PUP1 and PUP0, determine the
tPURST time delay. The nominal power up times are
shown in the following table.
WD1, WD0: Watchdog Timer Bits (Nonvolatile)
The bits WD1 and WD0 control the period of the
Watchdog Timer. The options are shown below.
Writing to the Control Registers
Changing any of the nonvolatile bits of the control and
trickle registers requires the following steps:
–Write a 02H to the Control Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation preceded
by a start and ended with a stop).
–Write a 06H to the Control Register to set the
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation proceeded by a start
and ended with a stop).
–Write a one byte value to the Control Register that
has all the control bits set to the desired state. The
Control register can be represented as qxys 001r in
binary, where xy are the WD bits, s isthe BP bit and
qr are the power up bits. This operation proceeded
by a start and ended with a stop bit. Since this is a
nonvolatile write cycle it will take up to 10ms to
complete. The RWEL bit is reset by this cycle and the
sequence must be repeated to change the nonvola-
tile bits again. If bit 2 is set to ‘1’ in this third step
(qxys 011r) then the RWEL bit is set, but the WD1,
WD0, PUP1, PUP0, and BP bits remain unchanged.
Writing a second byte to the control register is not
allowed. Doing so aborts the write operation and
returns a NACK.
–A read operation occurring between any of the
previous operations will not interrupt the register
write operation.
– The RWEL bit cannot be reset without writing to the
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write
protected block.
To illustrate, a sequence of writes to the device consist-
ing of [02H, 06H, 02H] will reset all of the nonvolatile
bits in the Control Register to 0. A sequence of [02H,
06H, 06H] will leave the nonvolatile bits unchanged
and the RWEL bit remains set.
FAULT DETECTION REGISTER
The Fault Detection Register (FDR) provides the user
the status of what causes the system reset active. The
Manual Reset Fail, Watchdog Timer Fail and three Low
Voltage Fail bits are volatile.
The FDR is accessed with a special preamble in the
slave byte (1011) and is located at address 0FFh. It
can only be modied by performing a byte write
operation directly to the address of the register and
only one data byte is allowed for each register write
operation.
There is no need to set the WEL or RWEL in the
control register to access this fault detection register.
BP
Protected Addresses
(Size)
Array Lock
0
None
1
100h – 1FFh (256 bytes)
Upper Half of
Memory Array
PUP1
PUP0
Power on Reset Delay (tPURST)
00
50ms
01
200ms (factory setting)
10
400ms
11
800ms
WD1
WD0
Watchdog Time Out Period
00
1.4 seconds
01
200 milliseconds
10
25 milliseconds
11
disabled (factory setting)
7
6543
2
1
0
LV1F
LV2F
0
WDF
0
相关PDF资料 |
PDF描述 |
|---|---|
| X5169S8I | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| X5643S14I | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| XA1N300M | POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.036A (COIL), 28VDC (COIL), 1008mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT |
| XJ7N300M | POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.036A (COIL), 28VDC (COIL), 1008mW (COIL), 5A (CONTACT), 28VDC (CONTACT), THROUGH HOLE-RIGHT ANGLE MOUNT |
| XA3S100E-4FGG400I | FPGA, 240 CLBS, 100000 GATES, 572 MHz, PBGA400 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40411S8I-CT1 | 功能描述:IC VOLTAGE MON DUAL W/SUP 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-A | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-AT1 | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-B | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-BT1 | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。