- 您现在的位置：买卖IC网 > PDF目录205930 > X40411S8I-C 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | X40411S8I-C |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | PLASTIC, SOIC-8 |
| 文件页数： | 5/25页 |
| 文件大小： | 532K |
| 代理商： | X40411S8I-C |
X40410/X40411/X40414/X40415
Characteristics subject to change without notice.
13 of 25
REV 1.3.6 2/11/04
www.xicor.com
– One bit of the slave command byte is a R/W bit. The
R/W bit of the Slave Address Byte denes the opera-
tion to be performed. When the R/W bit is a one, then
a read operation is selected. A zero selects a write
operation.
Word Address
The word address is either supplied by the master or
obtained from an internal counter. The internal counter
is undened on a power up condition.
Operational Notes
The device powers-up in the following state:
– The device is in the low power standby state.
– The WEL bit is set to ‘0’. In this state it is not possible
to write to the device.
–SDA pin is the input mode.
– RESET/RESET Signal is active for tPURST.
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
– The WEL bit must be set to allow write operations.
– The proper clock count and bit sequence is required
prior to the stop bit in order to start a nonvolatile write
cycle.
–A three step sequence is required before writing into
the Control Register to change Watchdog Timer or
Block Lock settings.
Figure 16. Sequential Read Sequence
Data
(2)
S
t
o
p
Slave
Address
Data
(n)
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
1
Data
(n-1)
A
C
K
A
C
K
(n is any integer greater than 1)
Data
(1)
Figure 15. Random Address Read Sequence
0
Slave
Address
Byte
Address
A
C
K
A
C
K
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
1
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from
the Master
10 1
0
相关PDF资料 |
PDF描述 |
|---|---|
| X5169S8I | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| X5643S14I | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| XA1N300M | POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.036A (COIL), 28VDC (COIL), 1008mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT |
| XJ7N300M | POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.036A (COIL), 28VDC (COIL), 1008mW (COIL), 5A (CONTACT), 28VDC (CONTACT), THROUGH HOLE-RIGHT ANGLE MOUNT |
| XA3S100E-4FGG400I | FPGA, 240 CLBS, 100000 GATES, 572 MHz, PBGA400 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40411S8I-CT1 | 功能描述:IC VOLTAGE MON DUAL W/SUP 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-A | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-AT1 | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-B | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40411V8-BT1 | 功能描述:IC VOLTAGE MON DUAL W/SUP 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。