收藏本站
参数资料
型号： XE8000EV104
厂商： Semtech
文件页数： 85/156页
文件大小： 0K
描述： EVAL BOARD FOR XE8805AMI028LF
标准包装： 1
类型： MCU
适用于相关产品： XE88LC05AMI028
所含物品： 完全组装的评估板
Semtech 2006
www.semtech.com
5-2
XE8805/05A
5.1
Overview
The XE8000 chips have three operating modes. There is the normal, the low current and the very low current
modes (see Figure 5-1). The different modes are controlled by the reset and clock blocks (see the documentation
of the respective blocks).
5.2
Operating mode
Start-up
All bits are reset in the design when a POR (power-on-reset) is active.
RC is enabled, Xtal is disabled and the CPU is reset (pmaddr = 0000).
If Port A is used to return from the sleep mode, all bits with resetcold don’t change (see sleep mode).
Reset
All bits with resetsystem and resetpconf (if enabled) are reset. Clock configuration doesn’t change except cpuck.
The CPU is reset.
Active mode
This is the mode where the CPU and all peripherals can work and execute the embedded software.
Standby mode
Executing a HALT instruction moves the XE8805 into the Standby mode. The CPU is stopped, but the clocks
remain active. Therefore, the enabled peripherals remain active e.g. for time keeping. A reset or an interrupt/event
request (if enabled) cancels the standby mode.
Sleep mode
This is a very low-power mode because all circuit clocks and all peripherals are stopped. Only some service blocks
remain active. No time-keeping is possible. Two instructions are necessary to move into sleep mode. First, the
SleepEn (sleep enable) bit in RegSysCtrl has to be set to 1. The sleep mode can then be activated by setting the
Sleep bit in RegSysReset to 1.
There are three possibe ways to wake-up from the sleep mode:
1.
The por (power-on-reset caused by a power-down followed by power-on). The RAM information is lost.
2.
The padreset
3.
The Port A reset combination (if the Port A is present in the product). See Port A documentation for
more details.
Note:
If the Port A is used to return from the sleep mode, all bits with resetcold don’t change (RegSysCtrl,
RegSysReset (except bit sleep), EnExtClock and BiasRc in RegSysClock, RegSysRcTrim1 and
RegSysRcTrim2). The SleepFlag bit in RegSysReset, reads back a 1 if the circuit was in sleep mode
since the flag was last cleared (see reset block for more details).
Note:
For a lower power consumption, disable the BiasRc bit in RegSysClock before to going to sleep mode.
The start-up time of the oscillator will then be longer however.
Note:
It is recommended to insert a NOP instruction after the instruction that sets the circuit in sleep mode
because this instruction can be executed when the sleep mode is left using the resetfromportA.
Not
Recommended
for
New
Designs
相关PDF资料
PDF描述
VE-B7P-EY CONVERTER MOD DC/DC 13.8V 50W
EBA28DRTH CONN EDGECARD .125 DIP 56POS
EEC20DRTH-S734 CONN EDGECARD 40POS DIP .100 SLD
AT-S-26-8/8/S-14-R MOD CORD STANDARD 8-8 SILVER 14'
EBC25DREN-S13 CONN EDGECARD 50POS .100 EXTEND
相关代理商/技术参数
参数描述
XE8000EV108 功能描述:EVAL BOARD FOR XE8806/XE8807 RoHS:否 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 产品培训模块:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板，软件，4x4 键盘，光学拨轮，QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
XE8000EV110 功能描述:EVAL BOARD FOR XE8802AMI035LF RoHS:否 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 产品培训模块:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板，软件，4x4 键盘，光学拨轮，QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
XE8000EV120 功能描述:BOARD EVAL FOR SX8722I070TRLF RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:ZoomingADC™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件
XE8000EV121 功能描述:BOARD EVAL FOR SX8723/24 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
XE8000MP 功能描述:PROG BOARD AND PROSTART2 CARD RoHS:否 类别:编程器，开发系统 >> 独立编程器 系列:- 产品目录绘图:CHIPPROG-G4 标准包装:1 系列:- 类型:成组编程器 适用于相关产品:EEPROM，EPROM，FLASH，MCU，NVRAM，PLD 所含物品:编程器，线缆，CD 产品目录页面:598 (CN2011-ZH PDF) 相关产品:AE-TS56-16I-3-ND - ISP CABLEADAPTER 14-PIN HEADERAE-TS40N-ND - ADAPTER SOCKET 40-TSOP TO 40-DIPAE-TS32N-ND - ADAPTER SOCKET 32-TSOP TO 32-DIPAE-TS28-ND - ADAPTER SOCKET 28-TSOP TO 28-DIPAE-T44-P16-ND - ADAPTER SOCKET 44-QFP TO 40-DIPAE-T44-I51/505-ND - ADAPTER SOCKET 44-QFP TO 40-DIPAE-SS56-16I-ND - ADAPTER SOCKET 56-SSOP TO 40-DIPAE-SP8U-ND - ADAPTER SOCKET 8-SSOP TO 8-DIPAE-SP28U2-ND - ADAPTER SOCKET 28-SSOP TO 28-DIPAE-SP28U1-ND - ADAPTER SOCKET 28-SSOP TO 28-DIP更多...
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*