- 您现在的位置：买卖IC网 > PDF目录16451 > XR16V794IV-0B-EVB (Exar Corporation)EVAL BOARD FOR XR16V794-B 64TQFP PDF资料下载
参数资料
| 型号： | XR16V794IV-0B-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 32/53页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16V794-B 64TQFP |
| 设计资源： | XR17V798/794 Eval Board Schematic |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
XR16V794
38
HIGH PERFORMANCE 2.25V TO 3.6V QUAD UART WITH FRACTIONAL BAUD RATE
REV. 1.0.1
MSR [3]: Transmitter Disable
This bit can be used to disable the transmitter by halting the Transmit Shift Register (TSR). When this bit is set
to a ’1’, the bytes already in the FIFO will not be sent out. Also, any more data loaded into the FIFO will stay in
the FIFO and will not be sent out. When this bit is set to a ’0’, the bytes currently in the TX FIFO will be sent
out. Please note that setting this bit to a ’1’ stops any character from going out. Also, this bit must be a ’0’ for
Send Char Immediate function (see MCR[3]).
Logic 0 = Enable Transmitter (default).
Logic 1 = Disable Transmitter.
MSR [2]: Receiver Disable
This bit can be used to disable the receiver by halting the Receive Shift Register (RSR). When this bit is set to
a ’1’, the receiver will not receive any more characters until it is enabled again by setting this bit to a ’0’. Data
currently in the RX FIFO can be read out. Please note that setting this bit to a ’1’ prevents any character from
coming in.
Logic 0 = Enable Receiver (default).
Logic 1 = Disable Receiver.
MSR [1:0]: Reserved
4.11
SCRATCH PAD REGISTER (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
4.12
FEATURE CONTROL REGISTER (FCTR) - Read/Write
This register controls the UART enhanced functions that are not available on ST16C554 or ST16C654.
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is
selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550
and ST16C650 series. RTS/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one
FIFO level above and one FIFO level below. See in Table 14 for complete selection with FCR bit 4-5 and
FCTR bit 6-7, i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR#
output will de-assert at 60 and re-assert at 16.
FCTR[5]: Auto RS485 Enable
Auto RS485 half duplex control enable/disable.
Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register
(THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out.
Logic 1 = Enable Auto RS485 half duplex direction control. RTS# output changes its logic level from HIGH to
LOW when finished sending the last stop bit of the last character out of the TSR register. It changes from
LOW to HIGH when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior
sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register
(TSR) empty.
FCTR[4]: Infrared RX Input Logic Select
Logic 0 = Select RX input as active HIGH encoded IrDA data, normal, (default).
Logic 1 = Select RX input as active LOW encoded IrDA data, inverted.
FCTR [3:0] - Auto RTS/DTR Flow Control Hysteresis Select
These bits select the auto RTS/DTR flow control hysteresis and only valid when TX and RX Trigger Table-D is
selected (FCTR bit-6 and 7 are set to logic 1). The RTS/DTR hysteresis is referenced to the RX FIFO trigger
level. After reset, these bits are set to logic 0 selecting the next FIFO trigger level for hardware flow control.
shows the 16 selectable hysteresis levels.
相关PDF资料 |
PDF描述 |
|---|---|
| 1-1906053-1 | CA 2MM OFNR 62.5/125,LC SEC YEL |
| D-1744-02 | SOLDERSLEEVE WIRE SPLICE .125" |
| GCC10DRAH-S734 | CONN EDGECARD 20POS .100 R/A SLD |
| A3977SLP-T | IC MOTOR DRIVER PWM DUAL 28-TSSO |
| 1-1906052-1 | CA 2MM OFNR 62.5/125,LC SEC BLU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V794IV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V798 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL |
| XR16V798_08 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL |
| XR16V798IQ | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL |
| XR16V798IQ-0A-EVB | 功能描述:UART 接口集成电路 Supports V798 100 ld QFP,ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。