- 您现在的位置：买卖IC网 > PDF目录16451 > XR16V794IV-0B-EVB (Exar Corporation)EVAL BOARD FOR XR16V794-B 64TQFP PDF资料下载
参数资料
| 型号： | XR16V794IV-0B-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 6/53页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16V794-B 64TQFP |
| 设计资源： | XR17V798/794 Eval Board Schematic |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
XR16V794
14
HIGH PERFORMANCE 2.25V TO 3.6V QUAD UART WITH FRACTIONAL BAUD RATE
REV. 1.0.1
2.11
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 18), the 794 compares one or two sequential receive data
characters with the programmed Xon-1,2 or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed Xoff-1,2 value(s), the 794 will halt transmission (TX) as soon as the current character has
completed transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the
interrupt output pin will be activated. Following a suspension due to a match of the Xoff character(s), the 794
will monitor the receive data stream for a match to the Xon-1,2 character(s). If a match is found, the 794 will
resume operation and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon1, Xon2, Xoff1 and Xoff2 flow control registers to ’0’. Following reset,
any desired Xon/Xoff value can be used for software flow control. Different conditions can be set to detect Xon/
Xoff characters (See Table 18) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters
are selected, the 794 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
FIGURE 9. AUTO RTS/DTR AND CTS/DSR FLOW CONTROL OPERATION
The local UART (UARTA) starts data transfer by asserting RTSA# (1). RTSA# is normally connected to CTSB# (2) of
remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO
(4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and con-
tinues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA
monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows
(7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its trans-
mit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9),
UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until
next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB
with RTSB# and CTSA# controlling the data flow.
RTSA#
CTSB#
RXA
TXB
Transmitter
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Auto CTS
Monitor
RTSA#
TXB
RXA FIFO
CTSB#
Remote UART
UARTB
Local UART
UARTA
ON
OFF
ON
Suspend
Restart
RTS High
Threshold
Data Starts
ON
OFF
ON
Assert RTS# to Begin
Transmission
1
2
3
4
5
6
7
Receive
Data
RTS Low
Threshold
9
10
11
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Transmitter
Auto CTS
Monitor
RTSB#
CTSA#
RXB
TXA
INTA
(RXA FIFO
Interrupt)
RX FIFO
Trigger Level
RX FIFO
Trigger Level
8
12
RTSCTS1
相关PDF资料 |
PDF描述 |
|---|---|
| 1-1906053-1 | CA 2MM OFNR 62.5/125,LC SEC YEL |
| D-1744-02 | SOLDERSLEEVE WIRE SPLICE .125" |
| GCC10DRAH-S734 | CONN EDGECARD 20POS .100 R/A SLD |
| A3977SLP-T | IC MOTOR DRIVER PWM DUAL 28-TSSO |
| 1-1906052-1 | CA 2MM OFNR 62.5/125,LC SEC BLU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V794IV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V798 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL |
| XR16V798_08 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL |
| XR16V798IQ | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL |
| XR16V798IQ-0A-EVB | 功能描述:UART 接口集成电路 Supports V798 100 ld QFP,ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。