参数资料
| 型号： | XRT73LC03AIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 25/61页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| 标准包装： | 72 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 3/3 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 120-LQFP |
| 供应商设备封装： | 120-LQFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
XRT73LC03A
29
REV. 1.0.4
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
1. In this mode, the Transmit Logic Block ignores the
TNData_(n) input pin.
2. If the Transmit Section of a given channel is config-
ured to accept Single-Rail data from the Terminal
Equipment, the B3ZS/HDB3 Encoder must be
enabled.
Figure 16 illustrates the behavior of the TPData_(n)
and TxClk_(n) signals when the Transmit Logic Block
has been configured to accept Single-Rail data from
the Terminal Equipment.
2.2
THE TRANSMIT CLOCK DUTY CYCLE ADJUST CIR-
CUITRY
The on-chip Pulse-Shaping circuitry within the Trans-
mit Section of each Channel in the XRT73LC03A
generates pulses of the appropriate shapes and width
to meet the applicable pulse template requirements.
The widths of these output pulses are defined by the
width of the half-period pulses within the TxClk_(n)
signal.
However, if the widths of the pulses within the
TxClk_(n) clock signal are allowed to vary significant-
ly, this could jeopardize the chip's ability to generate
Transmit Output pulses of the appropriate width and
thereby not meet the Pulse Template requirement
specification. Consequently, the chip's ability to gen-
erate compliant pulses could depend upon the duty
cycle of the clock signal applied to the TxClk_(n) input
pin.
The Transmit Clock Duty Cycle Adjust Circuitry ac-
cepts clock pulses via the TxClk_(n) input pin at duty
cycles ranging from 30% to 70% and converts them
to a 50% duty cycle.
2.3
THE HDB3/B3ZS ENCODER BLOCK
The purpose of the HDB3/B3ZS Encoder Block is to
aid in the Clock Recovery process at the Remote Ter-
minal Equipment by ensuring an upper limit on the
number of consecutive zeros that can exist within the
line signal.
2.3.1
B3ZS Encoding
If the XRT73LC03A has been configured to operate
in the DS3 or SONET STS-1 Modes, then the HDB3/
B3ZS Encoder blocks operate in the B3ZS Mode.
When the Encoder is operating in this mode, it parses
through and searches the Transmit Binary Data
Stream from the Transmit Logic Block for the occur-
rence of three (3) consecutive zeros (e.g., "000"). If
the B3ZS Encoder finds an occurrence of three con-
secutive zeros, then it substitutes these three "0’s",
with either a "00V" or a "B0V" pattern.
Where:
"B" represents a Bipolar pulse that is compliant with
the Alternating Polarity requirements of the AMI (Al-
ternate Mark Inversion) line code; and
"V" represents a Bipolar Violation (e.g., a bipolar
pulse that violates the Alternating Polarity require-
ments of the AMI line code).
The B3ZS Encoder decides whether to substitute
with either the “00V" or the "B0V" pattern in order to
insure that an odd number of bipolar pulses exist be-
tween any two consecutive violation pulses.
Figure 17 illustrates the B3ZS Encoder at work with
two separate strings of three (or more) consecutive
zeros
FIGURE 16. THE BEHAVIOR OF THE TPDATA AND TXCLK INPUT SGNALS, WHILE THE TRANSMIT LOGIC BLOCK IS
ACCEPTING SINGLE-RAIL DATA FROM THE TERMINAL EQUIPMENT
TxClk
TPData
Data
1
0
相关PDF资料 |
PDF描述 |
|---|---|
| XRT73LC04AIV-F | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| XRT73R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75L00DIV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT73LC04A | 制造商:EXAR 制造商全称:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04A_08 | 制造商:EXAR 制造商全称:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04AES | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| XRT73LC04AIV | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT73LC04AIV-F | 功能描述:外围驱动器与原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。