参数资料
| 型号： | XRT75L00DIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 33/92页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| 标准包装： | 96 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1，SONET |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-LQFP |
| 供应商设备封装： | 52-TQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
XRT75L00D
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
34
6.2
JITTER TRANSFER - RECEIVER/TRANSMITTER:
Jitter Transfer function is defined as the ratio of jitter on the output relative to the jitter applied on the input
versus frequency.
There are two distinct characteristics in jitter transfer: jitter gain (jitter peaking) defined as the highest ratio
above 0 dB; and jitter transfer bandwidth.The overall jitter transfer bandwidth is controller by a low bandwidth
loop,which is part of the XRT75L00D.
The jitter transfer function is a ratio between the jitter output and jitter input for a component, or system often
expressed in dB. A negative dB jitter transfer indicates the element removed jitter. A positive dB jitter transfer
indicates the element added jitter.A zero dB jitter transfer indicates the element had no effect on jitter.
Table 12 shows the jitter transfer characteristics and/or jitter attenuation specifications for various data rates:
The XRT75L00D meets the above Jitter Specifications.
6.3
JITTER GENERATION:
Jitter Generation is defined as the process whereby jitter appears at the output port of the digital equipment in
the absence of applied input jitter. Jitter Generation is measured by sending jitter free data to the clock and
data recovery circuit and measuring the amount of jitter on the output clock or the re-timed data. Since this is
essentially a noise measurement, it requires a definition of bandwidth to be meaningful. The bandwidth is set
according to the data rate. In general, the jitter is measured over a band of frequencies.
6.4
Jitter Attenuator:
An advanced crystal-less jitter attenuator is included in the XRT75L00D. The jitter attenuator uses the internal
reference clock.
In Host mode, by clearing or setting the JATx/Rx bit in the control register selects the jitter attenuator either in
the Receive or Transmit path. In Hardware mode, JATx/Rx pin selects the jitter attenuator in Receive or
Transmit path.
The FIFO is either a 16-bit, 32-bit or 128-bit register. In Host mode, the bits JA0 and JA1can be set to
appropriate combination to select the different FIFO sizes or to disable the jitter attenuator. In Hardware mode,
appropriate setting of the pins JA0 and JA1 selects the different FIFO sizes or disable the jitter attenuator. Data
is clocked into the FIFO with the associated clock signal (TxClk or RxClk) and clocked out of the FIFO with the
dejittered clock. When the FIFO is within two bits of overflowing or underflowing, the FIFO limit status bit, FL is
set to “1” in the Alarm status register. Reading this bit clears the FIFO and resets the bit into default state.
TABLE 11: JITTER AMPLITUDE VERSUS MODULATION FREQUENCY (JITTER TOLERANCE)
BIT RATE
(KB/S)
STANDARD
INPUT JITTER AMPLITUDE (UI
P
-P)
MODULATION FREQUENCY
A1
A2
A3
F
1(HZ)
F
2(HZ)
F
3(KHZ)
F
4(KHZ)
F
5(KHZ)
34368
ITU-T G.823
1.5
0.15
-
100
1000
10
800
-
44736
GR-499
CORE Cat I
5
0.1
-
10
2.3k
60
300
-
44736
GR-499
CORE Cat II
10
0.3
-
10
669
22.3
300
-
51840
GR-253
CORE Cat II
15
1.5
0.15
10
30
300
2
20
TABLE 12: JITTER TRANSFER SPECIFICATIONS
E3
DS3
STS-1
ETSI TBR-24
GR-499 CORE section 7.3.2
Category I and Category II
GR-253 CORE section 5.6.2.1
相关PDF资料 |
PDF描述 |
|---|---|
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L02DIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| XRT75L03DIV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L03IV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L04DIV-F | IC LIU E3/DS3/STS-1 4CH 176TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L00DIVTR | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00DIVTR-F | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00ES | 功能描述:时钟合成器/抖动清除器 1CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00IV | 功能描述:外围驱动器与原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT75L00IV-F | 功能描述:外围驱动器与原件 - PCI Sngl Chip LIU DS3/E3 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。