参数资料
| 型号： | XRT75L00DIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 61/92页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| 标准包装： | 96 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1，SONET |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-LQFP |
| 供应商设备封装： | 52-TQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
XRT75L00D
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.2
59
What does this mean at the "Destination" PTE?
In this case, this DS3 signal (which has now been mapped into an STS-1 data-stream) will be transported
across the SONET network. As this STS-1 signal arrives at the "Destination" PTE, this PTE will extract (or de-
map) this DS3 data from each incoming STS-1 SPE. Now, in this case most (e.g., 177/178.8) of the incoming
STS-1 SPEs will contain 5592 DS3 data-bits. Therefore, the nominal data rate of the DS3 signal being de-
mapped from SONET will be 44.736Mbps. However, in approximately 1 out of every 178 incoming STS-1
SPEs, the SPE will carry 5593 DS3 data-bits. This means that (during these times) the data rate of the de-
mapped DS3 signal will have an instantaneous frequency that is greater than 44.736Mbps. These "excursion"
of the de-mapped DS3 data-rate, from the nominal DS3 frequency can be viewed as occurrences of "mapping/
de-mapping" jitter. Since each of these "bit-stuffing" events involve the insertion of one DS3 data bit, we can
say that the amplitude of this "mapping/de-mapping" jitter is approximately 1UI-pp. From this point on, we will
be referring to this type of jitter (e.g., that which is induced by the mapping and de-mapping process) as "de-
mapping" jitter.
Since this occurrence of "de-mapping" jitter is periodic and occurs once every 22.35ms, we can state that this
jitter has a frequency of 44.7Hz.
9.2.2.3
The 44.736Mbps - 1ppm Case
In this case, let us assume that a DS3 signal, with a bit-rate of 44.736Mbps - 1ppm is being mapped into an
STS-1 signal with a bit-rate of 51.84Mbps + 0ppm. In this case, the following this will occur.
In general, most of the STS-1 SPEs will each transport 5592 DS3 data bits.
However, within a "one-second" period a DS3 signal that has a bit-rate of 44.736Mbps - 1ppm will deliver
approximately 45 too few bits below that of a DS3 signal with a bit-rate of 44.736Mbps + 0ppm. This means
that this particular signal will need to "positive-stuff" or exclude a DS3 data bit from mapping every (1/44.736)
= 22.35ms.
In other words, we will need to avoid mapping this DS3 data-bit about one in every
(22.35ms*8000) = 178.8 STS-1 SPEs.
What does this mean at the "Source" PTE?
All of this means that as the "Source" PTE maps this DS3 signal, with a data rate of 44.736Mbps - 1ppm into
an STS-1 signal, most of the resulting "outbound" STS-1 SPEs will transport 5592 DS3 data bits (e.g., 3 Stuff
Opportunity bits will be carrying DS3 data bits, the remaining 6 Stuff Opportunity bits are "stuff" bits). However,
in approximately one out of 178.8 "outbound" STS-1 SPEs, there will be a need for a "positive-stuffing" event.
Whenever these "positive-stuffing" events occur then (for these particular STS-1 SPEs) the SPE will carry only
5591 DS3 data bits (e.g., in this case, only 2 Stuff Opportunity bits will be carrying DS3 data-bits, and the
remaining 7 Stuff Opportunity bits are "stuff" bits).
Figure 40 presents an illustration of the STS-1 SPE traffic that will be generated by the "Source" PTE, during
this condition.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L02DIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| XRT75L03DIV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L03IV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L04DIV-F | IC LIU E3/DS3/STS-1 4CH 176TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L00DIVTR | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00DIVTR-F | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00ES | 功能描述:时钟合成器/抖动清除器 1CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00IV | 功能描述:外围驱动器与原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT75L00IV-F | 功能描述:外围驱动器与原件 - PCI Sngl Chip LIU DS3/E3 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。