参数资料
| 型号： | XRT75L00DIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 71/92页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| 标准包装： | 96 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1，SONET |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-LQFP |
| 供应商设备封装： | 52-TQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页当前第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
XRT75L00D
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
68
viewed as a 12-Channel DS3/STS-1 to STS-12 Mapper IC. Continuing on with this line of thought, if a Mapper
IC is configured to receive an STS-N signal, and (from this STS-N signal) de-map and output N DS3 signals
(towards the DS3 facility), then it will typically do so in the following manner.
In many cases, the Mapper IC will output this DS3 signal, using both a "Data-Signal" and a "Clock-Signal". In
many cases, the Mapper IC will output the contents of an entire STS-1 data-stream via the Data-Signal.
However, as the Mapper IC output this STS-1 data-stream, it will typically supply clock pulses (via the Clock-
Signal output) coincident to whenever a DS3 bit is being output via the Data-Signal. In this case, the Mapper
IC will NOT supply a clock pulse coincident to when a TOH, POH, or any "non-DS3 data-bit" is being output
via the "Data-Signal".
Now, since the Mapper IC will output the entire STS-1 data stream (via the Data-Signal), the output Clock-
Signal will be of the form such that it has a period of 19.3ns (e.g., a 51.84MHz clock signal). However, the
Mapper IC will still generate approximately 44,736,000 clock pulses during any given one second period.
Hence, the clock signal that is output from the Mapper IC will be a horribly gapped 44.736MHz clock signal.
One can view such a clock signal as being a very-jittery 44.736MHz clock signal. This jitter that exists within
the "Clock-Signal" is referred to as "Clock-Gapping" Jitter. A more detailed discussion on how the user must
handle this type of jitter is presented in “Section 9.8.2, Recommendations on Pre-Processing the Gapped
9.5
A Review of the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3
applications
The "Category I Intrinsic Jitter Requirements" per Telcordia GR-253-CORE (for DS3 applications) mandates
that the user perform a large series of tests against certain specified "Scenarios". These "Scenarios" and their
corresponding requirements is summarized in Table 18, below.
TABLE 18: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
COMMENTS
DS3 De-Mapping
Jitter
0.4UI-pp
Includes effects of De-Mapping and Clock Gapping Jitter
Single Pointer
Adjustment
A1
0.3UI-pp + Ao
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.NOTE: Ao is the amount
of intrinsic jitter that was measured during the "DS3 De-
Mapping Jitter" phase of the Test.
Pointer Bursts
A2
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Phase Transients
A3
1.2UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
87-3 Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
87-3 Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
87-3 Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Continuous Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L02DIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| XRT75L03DIV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L03IV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75L04DIV-F | IC LIU E3/DS3/STS-1 4CH 176TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L00DIVTR | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00DIVTR-F | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00ES | 功能描述:时钟合成器/抖动清除器 1CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00IV | 功能描述:外围驱动器与原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT75L00IV-F | 功能描述:外围驱动器与原件 - PCI Sngl Chip LIU DS3/E3 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。