XRT75R03DIV-F (Exar) PDF资料下载 Datasheet(19/135 页)

您好，
买卖IC网欢迎您。
请登录
免费注册

您现在的位置：买卖IC网 > PDF目录1977 > XRT75R03DIV-F (Exar Corporation)IC LIU E3/DS3/STS-1 3CH 128LQFP PDF资料下载

参数资料

型号：	XRT75R03DIV-F
厂商：	Exar Corporation
文件页数：	19/135页
文件大小：	0K
描述：	IC LIU E3/DS3/STS-1 3CH 128LQFP
标准包装：	72
类型：	线路接口装置（LIU）
驱动器/接收器数：	3/3
规程：	DS3，E3，STS-1
电源电压：	3.135 V ~ 3.465 V
安装类型：	表面贴装
封装/外壳：	128-LQFP
供应商设备封装：	128-LQFP（14x20）
包装：	托盘

第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页

XRT75R03D

111

REV. 1.0.4

THREE CHANNEL E3/DS3/STS-1 LINE

In this application, these Mapper devices can be thought of as multi-channel devices. For example, an STS-3

Mapper can be viewed as a 3-Channel DS3/STS-1 to STS-3 Mapper IC. Similarly, an STS-12 Mapper can be

viewed as a 12-Channel DS3/STS-1 to STS-12 Mapper IC. Continuing on with this line of thought, if a Mapper

IC is configured to receive an STS-N signal, and (from this STS-N signal) de-map and output N DS3 signals

(towards the DS3 facility), then it will typically do so in the following manner.

In many cases, the Mapper IC will output this DS3 signal, using both a "Data-Signal" and a "Clock-Signal".

In many cases, the Mapper IC will output the contents of an entire STS-1 data-stream via the Data-Signal.

However, as the Mapper IC output this STS-1 data-stream, it will typically supply clock pulses (via the Clock-

Signal output) coincident to whenever a DS3 bit is being output via the Data-Signal. In this case, the Mapper

IC will NOT supply a clock pulse coincident to when a TOH, POH, or any "non-DS3 data-bit" is being output

via the "Data-Signal".

Now, since the Mapper IC will output the entire STS-1 data stream (via the Data-Signal), the output Clock-

Signal will be of the form such that it has a period of 19.3ns (e.g., a 51.84MHz clock signal). However, the

Mapper IC will still generate approximately 44,736,000 clock pulses during any given one second period.

Hence, the clock signal that is output from the Mapper IC will be a horribly gapped 44.736MHz clock signal.

One can view such a clock signal as being a very-jittery 44.736MHz clock signal. This jitter that exists within

the "Clock-Signal" is referred to as "Clock-Gapping" Jitter. A more detailed discussion on how the user must

handle this type of jitter is presented in “Section 10.8.2, Recommendations on Pre-Processing the Gapped

Clocks (from the Mapper/ASIC Device) prior to routing this DS3 Clock and Data-Signals to the Transmit

Inputs of the XRT75R03D” on page 123

10.5

A Review of the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3

applications

The "Category I Intrinsic Jitter Requirements" per Telcordia GR-253-CORE (for DS3 applications) mandates

that the user perform a large series of tests against certain specified "Scenarios". These "Scenarios" and their

corresponding requirements is summarized in Table 31, below.

TABLE 31: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3

APPLICATIONS

SCENARIO

DESCRIPTION

SCENARIO

NUMBER

TELCORDIA GR-253-CORE

CATEGORY I INTRINSIC

JITTER REQUIREMENTS

COMMENTS

DS3 De-Mapping

Jitter

0.4UI-pp

Includes effects of De-Mapping and Clock Gapping Jit-

ter

Single Pointer

Adjustment

0.3UI-pp + Ao