参数资料
| 型号： | XRT83VSH28IB |
| 厂商： | Exar Corporation |
| 文件页数： | 16/75页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH E1 OCTAL 225BGA |
| 标准包装： | 84 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.14 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 225-BGA |
| 供应商设备封装： | 225-BGA（19x19） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
XRT83VSH28
20
REV. 2.0.0
8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
2.0
RECEIVE PATH LINE INTERFACE
The receive path of the XRT83VSH28 LIU consists of 8 independent E1 receivers. The following section
describes the complete receive path from RTIP/RRING inputs to RCLK/RPOS/RNEG outputs. A simplified
block diagram of the receive path is shown in Figure 3.
FIGURE 3. SIMPLIFIED BLOCK DIAGRAM OF THE RECEIVE PATH
2.1
Line Termination (RTIP/RRING)
2.1.1
CASE 1: Internal Termination
The input stage of the receive path accepts standard E1 twisted pair or E1 coaxial cable inputs through RTIP
and RRING. The physical interface is optimized by placing the terminating impedance inside the LIU. This
allows one bill of materials for all modes of operation reducing the number of external components necessary
in system design. The receive termination impedance is selected by programming TERSEL to match the line
impedance. Selecting the internal impedance is shown in Table 2.
The XRT83VSH28 has the ability to switch the internal termination to "High" impedance by programming
RxTSEL in the appropriate channel register. For internal termination, set RxTSEL to "1". By default, RxTSEL
is set to "0" ("High" impedance). For redundancy applications, a dedicated hardware pin (RxTSEL) is also
available to control the receive termination for all channels simultaneously. This hardware pin takes priority
over the register setting if RxTCNTL is set to "1" in the appropriate global register. If RxTCNTL is set to "0", the
state of this pin is ignored. See Figure 4 for a typical connection diagram using the internal termination.
FIGURE 4. TYPICAL CONNECTION DIAGRAM USING INTERNAL TERMINATION
TABLE 2: SELECTING THE INTERNAL IMPEDANCE
TERSEL
RECEIVE TERMINATION
0h
75
1h
120
HDB3 Decoder
Rx Jitter
Attenuator
Clock & Data
Recovery
Peak Detector
& Slicer
RTIP
RRING
RCLK
RNEG
RPOS
RTIP
RRING
XRT83VSH28 LIU
1:1
Internal Impedance
Line Interface E1
One Bill of Materials
Receiver
Input
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83VSH314IB-F | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83VSH316IB | IC LIU SH T1/E1/J1 16CH 316STBGA |
| XRT83VSH38IB | IC LIU SH T1/E1/J1 8CH 225BGA |
| XRT85L61IG | IC BITS CLOCK EXTRACTOR 28TSSOP |
| XRT91L30IQ | IC TXRX SONET/SDH 8BIT 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83VSH28IB-F | 功能描述:外围驱动器与原件 - PCI 8 Channel 1.8V-3.3V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH28IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT83VSH314 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314ES | 功能描述:外围驱动器与原件 - PCI 14 CHT1/E1LIUSH LOW COST VERSION RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH314IB | 功能描述:接口 - 专用 14 CH, SH T1/E1 1.8V DGTL/3.3V ANLG RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。