参数资料
| 型号： | XRT83VSH28IB |
| 厂商： | Exar Corporation |
| 文件页数： | 38/75页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH E1 OCTAL 225BGA |
| 标准包装： | 84 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.14 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 225-BGA |
| 供应商设备封装： | 225-BGA（19x19） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
XRT83VSH28
40
REV. 2.0.0
8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
5.1.2
24-Bit Serial Data Input Descritption
The serial data input is sampled on the rising edge of SCLK. In readback mode, the serial data output is
updated on the falling edge of SCLK. The serial data must be applied to the LIU LSB first. The 24 bits of serial
data are described below.
5.1.3
ADDR[7:0] (SCLK1 - SCLK8)
The first 8 SCLK cycles are used to provide the address to which a Read or Write operation will occur.
ADDR[0] (LSB) must be sent to the LIU first followed by ADDR[1] and so forth until all 8 address bits have been
sampled by SCLK.
5.1.4
R/W (SCLK9)
The next serial bit applied to the LIU informs the microprocessor that a Read or Write operation is desired. If
the R/W bit is set to “0”, the microprocessor is configured for a Write operation. If the R/W bit is set to “1”, the
microprocessor is configured for a Read operation.
5.1.5
Dummy Bits (SCLK10 - SCLK16)
The next 7 SCLK cycles are used as dummy bits. Seven bits were chosen so that the serial interface can easily
be divided into three 8-bit words to be compliant with standard serial interface devices. The state of these bits
are ignored and can hold either “0” or “1” during both Read and Write operations.
5.1.6
DATA[7:0] (SCLK17 - SCLK24)
The next 8 SCLK cycles are used to provide the data to be written into the internal register chosen by the
address bits. DATA[0] (LSB) must be sent to the LIU first followed by DATA[1] and so forth until all 8 data bits
have been sampled by SCLK. Once 24 SCLK cycles have been completed, the LIU holds the data until CS is
pulled “High” whereby, the serial microprocessor latches the data into the selected internal register.
5.1.7
8-Bit Serial Data Output Description
The serial data output is updated on the falling edge of SCLK17 - SCLK24 if R/W is set to “1”. DATA[0] (LSB) is
provided on SCLK17 to the SDO pin first followed by DATA[1] and so forth until all 8 data bits have been
updated. The SDO pin allows the user to read the contents stored in individual registers by providing the
desired address on the SDI pin during the Read cycle.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83VSH314IB-F | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83VSH316IB | IC LIU SH T1/E1/J1 16CH 316STBGA |
| XRT83VSH38IB | IC LIU SH T1/E1/J1 8CH 225BGA |
| XRT85L61IG | IC BITS CLOCK EXTRACTOR 28TSSOP |
| XRT91L30IQ | IC TXRX SONET/SDH 8BIT 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83VSH28IB-F | 功能描述:外围驱动器与原件 - PCI 8 Channel 1.8V-3.3V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH28IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT83VSH314 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314ES | 功能描述:外围驱动器与原件 - PCI 14 CHT1/E1LIUSH LOW COST VERSION RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH314IB | 功能描述:接口 - 专用 14 CH, SH T1/E1 1.8V DGTL/3.3V ANLG RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。